XQEAWT-00-0000-00000LEE1 (CREE)
LEDs

No Preview Available !

Click to Download PDF File for PC

Product family data sheet
Cree® XLamp® XQ-E LEDs
Product Description
The XLamp XQ-E LED family packs
the lighting-class performance of
the XP-E2 into a package that is 78
percent smaller. The compact XQ-E
LED enables lighting manufacturers
to significantly reduce the size and
total cost of their LED luminaires,
without sacrificing light output,
efficacy or reliability.
The new XQ-E LEDs open up new
design possibilities for a wide
spectrum of lighting applications
such as portable, indoor directional,
architectural or vehicle lighting. The
XQ-E’s combination of consistent
design across all configurations
and its small size permit improved
color mixing and optical control,
compared to the larger XP-E2 LED.
FEATURES
Cree’s smallest lighting class
LED: 1.6 X 1.6 X 1.44 mm
Available in 70- and
80-minimum CRI white, blue,
green and red
1 A maximum drive current
Wide viewing angle: white 110°,
blue & green 125°, red 130°
• Reflow solderable - JEDEC
J-STD-020C compatible
• Unlimited floor life at
≤ 30 °C/85% RH
• UL‑recognized component
(E349212)
Table of Contents
Characteristics........................... 2
Flux Characteristics - White......... 3
Flux Characteristics - Color.......... 4
Relative Spectral Power
Distribution............................... 5
Relative Flux vs. Junction
Temperature.............................. 6
Electrical Characteristics.............. 7
Relative Flux vs. Current............. 8
Typical Spatial Distribution........... 9
Thermal Design.........................10
Reflow Soldering Characteristics..11
Notes.......................................12
Mechanical Dimensions..............13
Tape and Reel...........................14
Packaging.................................15
Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice.
Cree®, the Cree logo and XLamp® are registered trademarks of Cree, Inc.
Cree, Inc.
4600 Silicon Drive
Durham, NC 27703
USA Tel: +1.919.313.5300
Free Datasheet http://www.datasheet4u.com/


XQEAWT-00-0000-00000LEE1 (CREE)
LEDs

No Preview Available !

Click to Download PDF File for PC

Characteristics
Characteristics
Thermal resistance, junction to solder point - white, blue
Thermal resistance, junction to solder point - green
Thermal resistance, junction to solder point - red
Viewing angle (FWHM) - white
Viewing angle (FWHM) - blue, green
Viewing angle (FWHM) - red
Temperature coefficient of voltage - white
Temperature coefficient of voltage - blue
Temperature coefficient of voltage - green
Temperature coefficient of voltage - red
ESD withstand voltage (HBM per Mil-Std-883D)- white, blue, green
ESD classification (HBM per Mil-Std-883D) - red
DC forward current
Reverse voltage
Forward voltage (@ 350 mA, 85 °C) - white
Forward voltage (@ 350 mA, 25 °C) - blue
Forward voltage (@ 350 mA, 25 °C) - green
Forward voltage (@ 350 mA, 25 °C) - red
LED junction temperature
xlamp xQ-e leds
Unit
°C/W
°C/W
°C/W
degrees
degrees
degrees
mV/°C
mV/°C
mV/°C
mV/°C
V
mA
V
V
V
V
V
°C
Minimum
Typical
6
9
5
110
125
130
-2.3
-3.3
-3.8
-1.8
Class 2
2.9
3.1
3.2
2.2
Maximum
8000
1000
5
3.25
3.5
3.6
2.6
150
Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks
of Cree, Inc.
2
Free Datasheet http://www.datasheet4u.com/


XQEAWT-00-0000-00000LEE1 (CREE)
LEDs

No Preview Available !

Click to Download PDF File for PC

xlamp xQ-e leds
Flux Characteristics - White (TJ = 85 °C)
The following table provides several base order codes for XLamp XQ-E white LEDs. It is important to note that the base
order codes listed here are a subset of the total available order codes for the product family. For more order codes,
as well as a complete description of the order-code nomenclature, please consult the XLamp XQ Family Binning and
Labeling document.
Color
CCT Range
Min.
Max.
Cool White 5000 K
8300 K
70-CRI
White
3700 K
8300 K
Neutral
White
3700 K
5300 K
80-CRI
White
2700 K
3500 K
Warm
White
2700 K
3500 K
Base Order Codes
Min. Luminous Flux (lm)
@ 350 mA
Group
Flux (lm) Flux (lm)
@ 85 °C @ 25 °C*
R2 114 132
Calculated Minimum
Luminous Flux (lm)**
@ 85 °C
700 mA
1.0 A
196 252
Order Code
XQEAWT-00-0000-00000LEE1
Q5 107 124 184 237 XQEAWT-00-0000-00000LDE1
R2 114 132 196 252 XQEAWT-00-0000-00000BEE1
Q5 107 124 184 237 XQEAWT-00-0000-00000BDE1
R2 114 132 196 252 XQEAWT-00-0000-00000LEE4
Q5 107 124 186 236 XQEAWT-00-0000-00000LDE4
Q4 100 116 172 221 XQEAWT-00-0000-00000LCE4
Q4 100 116 172 221 XQEAWT-00-0000-00000HCE7
Q3
93.9
111
162
208 XQEAWT-00-0000-00000HBE7
Q2
87.4
101
150
193 XQEAWT-00-0000-00000HAE7
Q4 100 116 172 221 XQEAWT-00-0000-00000LCE7
Q3
93.9
111
162
208 XQEAWT-00-0000-00000LBE7
Q2
87.4
101
150
193 XQEAWT-00-0000-00000LAE7
Notes:
• Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy)
measurements and ±2 on CRI measurements.
Typical CRI for Cool White (5000 K – 8300 K CCT) is 70.
Typical CRI for Neutral White (3700 K – 5300 K CCT) is 75.
Typical CRI for Warm White (2700 K – 3500 K CCT) is 80.
Minimum CRI for 70-CRI White is 70.
Minimum CRI for 80-CRI White is 80.
* Flux values @ 25 °C are calculated and for reference only.
** Calculated flux values at 700 mA and 1 A are for reference only.
Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks
of Cree, Inc.
3
Free Datasheet http://www.datasheet4u.com/


XQEAWT-00-0000-00000LEE1 (CREE)
LEDs

No Preview Available !

Click to Download PDF File for PC

xlamp xQ-e leds
Flux Characteristics - Color (TJ = 25 °C)
The following table provides several base order codes for XLamp XQ-E color LEDs. It is important to note that the base
order codes listed here are a subset of the total available order codes for the product family. For more order codes,
as well as a complete description of the order-code nomenclature, please consult the XLamp XQ Family Binning and
Labeling document.
Color
Blue
Dominant Wavelength Range
Min.
Group
DWL
(nm)
Max.
Group
DWL
(nm)
B3 465 B6 485
Base Order
Codes Min.
Luminous Flux
(lm) @ 350 mA
Group
Flux
(lm)
M2 39.8
K3 35.2
K2 30.6
Order Code
XQEBLU-00-0000-000000201
XQEBLU-00-0000-000000Z01
XQEBLU-00-0000-000000Y01
Color
Green
Dominant Wavelength Range
Min.
Max.
Group
DWL
(nm)
Group
DWL
(nm)
G2 520 G4 535
Base Order
Codes Min.
Luminous Flux
(lm) @ 350 mA
Group
Flux
(lm)
R2 114
Q5 107
Q4 100
Q3 93.9
Order Code
XQEGRN-00-0000-000000E01
XQEGRN-00-0000-000000D01
XQEGRN-00-0000-000000C01
XQEGRN-00-0000-000000B01
Color
Red
Dominant Wavelength Range
Min.
Max.
Group
DWL
(nm)
Group
DWL
(nm)
R2 620 R3 630
Base Order
Codes Min.
Luminous Flux
(lm) @ 350 mA
Group
Flux
(lm)
P3 73.9
P2 67.2
N4 62
N3 56.8
Order Code
XQERED-00-0000-000000801
XQERED-00-0000-000000701
XQERED-00-0000-000000601
XQERED-00-0000-000000501
Note: Cree maintains a tolerance of ±  7% on flux and power measurements and ±  1  nm on dominant wavelength
measurements.
Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks
of Cree, Inc.
4
Free Datasheet http://www.datasheet4u.com/


XQEAWT-00-0000-00000LEE1 (CREE)
LEDs

No Preview Available !

Click to Download PDF File for PC

xlamp xQ-e leds
Relative Spectral Power
Relative Spectral Power Distribution
100
80
60
Cool White
Warm White
40
20
0
380 430 480 530 580 630 680 730 780
Wavelength (nm)
Relative Spectral Power
100
80
60 Blue
Green
40 Red
20
0
380 430 480 530 580 630 680 730 780
Wavelength (nm)
Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks
of Cree, Inc.
5
Free Datasheet http://www.datasheet4u.com/


XQEAWT-00-0000-00000LEE1 (CREE)
LEDs

No Preview Available !

Click to Download PDF File for PC

xlamp xQ-e leds
Relative Flux Output vs. Junction Temperature
Relative Flux vs. Junction Temperature (IF = 350 mA)
120
100
80
60 White
40
20
0
25 50 75 100 125 150
Relative Flux OutJpunucttionvTsem.pJeruatnurec(tºiCo) n Temperature
100
90
80
70
60
50
40
30
20
10
0
25
Blue
Green
Red
50
75
100
125
Junction Temperature (ºC)
150
Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks
of Cree, Inc.
6
Free Datasheet http://www.datasheet4u.com/


XQEAWT-00-0000-00000LEE1 (CREE)
LEDs

No Preview Available !

Click to Download PDF File for PC

Electrical Characteristics (Tj = 85ºC)
xlamp xQ-e leds
Electrical Characteristics (TJ = 85 °C)
1000
800
600
White
400
200
0
1.90
2.10
2.30
2.50
2.70
2.90
3.10
Forward Voltage (V)
Electrical Characteristics (Tj = 85ºC)
3.30
3.50
Electrical Characteristics (TJ = 25 °C)
1000
800
600 Blue
Green
400 Red
200
0
1.90 2.10 2.30 2.50 2.70 2.90 3.10 3.30 3.50 3.70
Forward Voltage (V)
Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks
of Cree, Inc.
7
Free Datasheet http://www.datasheet4u.com/


XQEAWT-00-0000-00000LEE1 (CREE)
LEDs

No Preview Available !

Click to Download PDF File for PC

Relative Intensity vs. Current (Tj = 85ºC)
Relative Flux vs. Current (TJ = 85 °C)
250
xlamp xQ-e leds
200
150
White
100
50
0
0
100
200
300
400
500
600
700
800
900
1000
Forward Current (mA)
Relative Intensity vs. Current (Tj = 85ºC)
Relative Flux vs. Current (TJ = 25 °C)
300
250
200
Blue
150 Green
Red
100
50
0
0 100 200 300 400 500 600 700 800 900 1000
Forward Current (mA)
Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks
of Cree, Inc.
8
Free Datasheet http://www.datasheet4u.com/


XQEAWT-00-0000-00000LEE1 (CREE)
LEDs

No Preview Available !

Click to Download PDF File for PC

xlamp xQ-e leds
Typical Spatial Radiation Pattern-white
Typical Spatial Distribution
100
80
60
White
40
20
0
Typical-9S0 patia-l70Radia-t5i0on Pa-t3t0ern-roA-1yn0galleb(lºu)1e0, blue,30green,50amber7,0red-or90ange, red
100
80
60
Blue, Green
40 Red
20
0
-90 -70 -50 -30 -10 10 30 50 70 90
Angle (º)
Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks
of Cree, Inc.
9
Free Datasheet http://www.datasheet4u.com/


XQEAWT-00-0000-00000LEE1 (CREE)
LEDs

No Preview Available !

Click to Download PDF File for PC

xlamp xQ-e leds
Thermal Design
The maximum forward current is determined by the thermal resistance between the LED junction and ambient. It is
crucial for the end product to be designed in a manner that minimizes the thermal resistance from the solder point to
Thaemrbmieantl iDneosrdigenr t-o wophtiimteize lamp life and optical characterisTthicesr. mal Design - royal blue, blue
White Blue
1200
1200
1000
1000
800 800
600
Rj-a = 10 °C/W
Rj-a = 15 °C/W
400 Rj-a = 20 °C/W
200
600
Rj-a = 10 °C/W
Rj-a = 15 °C/W
400 Rj-a = 20 °C/W
Rj-a = 25 °C/W
200
0
0 20 40 60 80 100 120 140
Ambient Temperature (ºC)
0
0 20 40 60 80 100 120
Ambient Temperature (ºC)
Thermal Design - green
Thermal Design - amber, red-orange, red
Green Red
1200
1200
140
1000
1000
800 800
600
Rj-a = 15 °C/W
400
Rj-a = 20 °C/W
Rj-a = 25 °C/W
Rj-a = 30 °C/W
200
600
Rj-a = 10°C/W
Rj-a = 15°C/W
400 Rj-a = 20°C/W
Rj-a = 25°C/W
200
0
0 20 40 60 80 100 120 140
Ambient Temperature (ºC)
0
0 20 40 60 80 100 120 140
Ambient Temperature (ºC)
Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks
of Cree, Inc.
10
Free Datasheet http://www.datasheet4u.com/


XQEAWT-00-0000-00000LEE1 (CREE)
LEDs

No Preview Available !

Click to Download PDF File for PC

xlamp xQ-e leds
Reflow Soldering Characteristics
In testing, Cree has found XLamp XQ-E LEDs to be compatible with JEDEC J-STD-020C, using the parameters listed
below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the
manufacturer of solder paste used.
Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment.
Profile Feature
Average Ramp-Up Rate (Tsmax to Tp)
Preheat: Temperature Min (Tsmin)
Preheat: Temperature Max (Tsmax)
Preheat: Time (tsmin to tsmax)
Time Maintained Above: Temperature (TL)
Time Maintained Above: Time (tL)
Peak/Classification Temperature (Tp)
Time Within 5 °C of Actual Peak Temperature (tp)
Ramp-Down Rate
Time 25 °C to Peak Temperature
Lead-Based Solder
3 °C/second max.
100 °C
150 °C
60-120 seconds
183 °C
60-150 seconds
215 °C
10-30 seconds
6 °C/second max.
6 minutes max.
Lead-Free Solder
3 °C/second max.
150 °C
200 °C
60-180 seconds
217 °C
60-150 seconds
260 °C
20-40 seconds
6 °C/second max.
8 minutes max.
Note: All temperatures refer to topside of the package, measured on the package body surface.
Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks
of Cree, Inc.
11
Free Datasheet http://www.datasheet4u.com/


XQEAWT-00-0000-00000LEE1 (CREE)
LEDs

No Preview Available !

Click to Download PDF File for PC

xlamp xQ-e leds
Notes
Lumen Maintenance Projections
Cree now uses standardized IES LM-80-08 and TM-21-11 methods for collecting long-term data and extrapolating LED
lumen maintenance. For information on the specific LM-80 data sets available for this LED, refer to the public LM-80
results document at www.cree.com/xlamp_app_notes/LM80_results.
Please read the XLamp Long-Term Lumen Maintenance application note at www.cree.com/xlamp_app_notes/lumen_
maintenance for more details on Cree’s lumen maintenance testing and forecasting. Please read the XLamp Thermal
Management application note at www.cree.com/xlamp_app_notes/thermal_management for details on how thermal
design, ambient temperature, and drive current affect the LED junction temperature.
Moisture Sensitivity
In testing, Cree has found XLamp XQ-E LEDs to have unlimited floor life in conditions ≤ 30 ºC/85% relative humidity
(RH). Moisture testing included a 168-hour soak at 85 ºC/85% RH followed by 3 reflow cycles, with visual and electrical
inspections at each stage.
Cree recommends keeping XLamp LEDs in their sealed moisture-barrier packaging until immediately prior to use. Cree
also recommends returning any unused LEDs to the resealable moisture-barrier bag and closing the bag immediately
after use.
UL Recognized Component
Level 1 enclosure consideration. The LED package or a portion thereof has not been investigated as a fire enclosure or
a fire and electrical enclosure per ANSI/UL 8750.
Vision Advisory Claim
WARNING: Do not look at exposed lamp in operation. Eye injury can result. See LED Eye Safety at www.cree.com/
xlamp_app_notes/led_eye_safety.
Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks
of Cree, Inc.
12
Free Datasheet http://www.datasheet4u.com/


XQEAWT-00-0000-00000LEE1 (CREE)
LEDs

No Preview Available !

Click to Download PDF File for PC

66 5 55 4 44
NONTOICTEICE
ADNNETNDIATTLIAH. TLEH. ITNISHFPIOSLROPMLTOAATTNIAODNNTDHTEHINE FINOFROMRAMTAIOTNION
OIWTPHRITINEHTIANARRAEYRTAEHNTEDHPERPORPORPIERTIAETRAYRAYNADND
LFIAICNLRFIENOEFR,OMINRACMT. AITOHTNIIOSONPFLOOCFRTCERE,EIEN, CIN. TCH. TISHPISLOPLTOT
EOECDPOIEOPDRIE, DDREI,SRPCERLPOORDSOUEDDCUETCDOEODARNODYRISDCISLCOLSOEDSETDOTAONAYNY
OEZDUETPDEPRESROSNTOHNWE IWWTHRITOITHUTOETUNTCONTSHETENHTWERWITRTIETNTECNOCNOSNENSETNT
. Mechanical Dimensions
3 33
REV
A
All dimensions in mm.
Measurement tolerances unless indicated otherwise: .xx = .25 mm, .xxx = .125 mm
1.60 1.610.60
.600
2
REVREV
AA
xlamp xQ-e leds
22
REVISONS
REVRIESVOINSOS NS
DESCRIPTION
DESDCERSIPCTRIIOPTNION
BY
Initial Release InitIniailtiRael lReealseease
DDS
1
DATE
7/19/13
AP
D
.60.6000
.60.6000
1.60 1.610.60
1.500
1.510.5000
NOTCH IS ON NONTOCTHCHISIOSNON
CATHODE(-) SIDCAECTAHTOHDOED(-E)(S-)IDSIE
Top View
NOTICE
DENTIAL. THIS PLOT AND THE INFORMATION
MeasurementWITHIN ARE THE PROPRIETARY AND
IAL INFORMATION OF CREE, INC. THIS PLOT
E COPIED, REPRODUCED OR DISCLOSED TO ANY
ZED PERSON WITHOUT THE WRITTEN CONSENT
tolerance:
.xx
=
.13 mm
1.44 ±.05 1.414.4±4.0±5.05
Side View
NOTICE
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
CONTAINED WITHIN ARE THE PROPRIETARY AND
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT
OF CREE INC.
0.65
11.6.5000
1.510.5000
.300 .30.3000
.300 .30.3000
Bottom View
1.32
0.51
0.50
.65 .65.65
.30 .30.30
0.50
SOLDER PAD SOSLODLEDREPRAPDAD
REFERENCE RERFEEFREERNECNECE
1.60
1.32
1.610.60
3.300
3.30.3000
1.60ND THE INFORMATION
RIETARY AND
CREE, INC. THIS PLOT
CED OR DISCLOSED TO ANY
THE WRITTEN CONSENT
1.610.60
0.30
NOTICE
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
CONTAINED WITHIN ARE THE PROPRIETARY AND
RecoRmECmOMeMEnNdDEeDdPCPBOCARBD SsOoLDldERePrADpadCONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT
OF CREE INC.
0.30
RecoRmECmOMeMnENdDEeDdSTsENtCeILnOcPiElNIoNGpening
NDERDERPCECOCMBOOMAEMRNEDDNSEDODELDPDCPEBRCOPBAORDADRDSOSLODLEDREPRAPDAD
THIRD ANGLE PROJECTION
54
66 5
0.30
4.85
0.30
UNLESS OTHERWISE SPECIFIED
3.300 3.30.3000DIMENSIONS ARE IN
MILLIMETERS & BEFORE FINISH.
SOLDER PADTOLERANCE UNLESS SPECIFIED:
REFERENCE.X ± 0.3
RECOMMENDERDERTCEROCAMOCME EMLNAEYDNOEDDUETDTRTARCAECLEAXLYAQOYUOPTUCTB SOLDER PAD XQ STENCIL OPENING.XX ± .13
SOLDER PADX° ± 1°
REXFQEEROENUCTLEINEXQXEQOE UOTULTINLFOR SHEET METAL PARTS ONLY
.X ± .25
A XQ_PCBSolderPad -- -- -- A XQ_StencilOpening.XX ± .10
C 2C6C10-00035 2621601-00-X° ± 2°
DRAWN BY
M.Youmans
CHECK
APPROVED
MATERIAL
DATE
8/7/2013
DATE
DATE
FINAL PROTECTIVE FINISH
Santa Barbara Technology Center
340 Storke Rd
Goleta, CA 93117
Phone (805) 968-9460
Fax (805) 968-9811
MUILNLILMEDSESTIMEORETSNHASEINRODWNSIASFAEDUTMTORINSMIELLELPREMEELEINRSNIFUCIMSLSAIINMNILNFEOOILICUITNMSETLEENHESHDLDSEEURIL.ASTMIRNEMRSEOWDSLEEREE&STTIISNISMSNHEOBESASREETEINSSSRNOHFPPDWASNEEOEINCRSIACOCDRSDIHWIRFFNAEFEAETIIRESIAECDSWESFDEKDPFARE.NI:TENISRSNFBCEeIEPYISRINiFEbIHNFIICSEe.IINHDlFI.ISEHDMDC..RHYoAEuWCmDDKNAA7aTT/nBEECD1sYHR9AE/CDDW1HKR3.NAESCDWBeKY.Ni8bSDD/B7eAAY/ilTT2b0EEe1l3
DATDE ATE
7/179/193/13
DATSDEanAtTaEBarbara Technology Center
TITLE:
SIZE DWG. NO.
THIRD ANGLE PROJETCHTTRTIHROHEIDNRVIRDADNAAGNNLGEGLLEPERPTOPFROROJOLEOREJCRSJETEAHCICNEOTETCNTIIEOOM..XUXXNN°ENXXTXLAELS±SP±±ASFPROETRTCSFOS.I..O5OF21HLTI52RNEFEOEODRSLLTAHY:R.EX.XMNXERSEECAHTTENEAM±..X±E±ULCXXT0.°1ENEPXX1.°T3AM3X..XLUXXARE°ENXXMTALSTSXLP±SAAPET±OASRJLSEN.OPRR±SP±NLEIVT±AAYSECSeLPDR-.I..v-5OF21ETiI52CnSNE5°.I..sD5LOF21YI52:NE5°DLMAY:PAPTREDORA7IVAT/EEMA1LDP-9A-PT/MRAJE1.OPRA3NPIVTARJEEeL.OD-Rv-NIVAiDEneLD-AsvT-TIiTnELsE
TIT--LE--:
DATDE ATE
7/179/193/13 TITLTEITLE
SIZE DWG. NO.
.X ±
.XX ±
1.5
.75
.X
.XX
±..±XX..X2150..XXX±±
±
±
1.5 1.5
.75 .75
FINAL
PROTECTIVE
FINISHSIZE
DRAWSINIZGESNIZOE.
SCALE 50:1
SHEET 1 OF 1
.XXX ±
X° ±
.25
.5 °
.X±X2X.X°FXINXAL±PRO±TEC.2TIV5E.F2IN5ISH
± ± .5 °.5 °
FINALFIPNRAOLTPERCOTITVEECFTIINVIESHFINISH
SCALE 50:1
340 Storke Rd
460G0oSleilticao, nCDAri9ve3117
DuPrhhaomn,eN(.8C0257)790368-9
PhFonaex((981095) )31936-85-390801
Fax (919) 313-5558
RE
DRADWRINAWG INNOG. NO.
R
SHEET 1 OF
-- -- --3
2
51
4
SURFACE FINISH:
1.S6URSFUARCFEAFC3IENFISINHI:SH: 1.6 1.6
2SCALE 45.000
SCALSECAL4E5.04050.000
1SHEET
OF
55
4 5.00
44
3 33
2 10.02 02
1
5.00
ReRcEoCOmMmMEeNnDEdDeTRdACtrEaLAcYeOUlTa: MyoCPuCtB: MCPCB
10.00
RREeCcOoMmMEmNDeEDnTdRAeCdE tLArYaOcUeT: FlRa4yout: FR4
.Copyright © 2013 Cree,
of Cree, Inc.
13THIRD ANGLE PROJECTION
UNLESS OTHERWISE SPECIFIED
DRAWN BY
DATE
DIMENSIONS ARE IN
M.Youmans
8/7/2013
MILLIMETERS & BEFORE FINISH. CHECK
DATE
InTcO.LEARAlNlCErUigNLhEStSsSPrECeIFsIEeD:rved. The information
.X ± 0.3
APPROVED
DATE
.XX ± .13
X° ± 1°
MATERIAL
FOR SHEET METAL PARTS ONLY
340 Storke Rd
Goleta, CA 93117
Phone (805) 968-9460
inSatntha Biasrbarda Toecchnuolomgy Ceentner t is subjFeacx t(80t5o) 96c8h-98a1n1 ge without
TITLE:
RECOMMENDED TRACE LAYOTUHTIR: DMACNGPLCEBPROJECTION
SIZE DWG. NO.
REV
UNLESS OTHERWISE SPECIFIED
DRAWN BY
DIMENSIONS ARE IN
M.Youmans
MILLIMETERS & BEFORE FINISH. CHECK
noTOtLiEcReAN.CECUrNeLEeSS®S,PEtChIFIEeD: Cree logo and
.X ± 0.3
APPROVED
.XX ± .13
X° ± 1°
MATERIAL
FOR SHEET METAL PARTS ONLY
DATE
8/7/2013
DATE
XLamp®
DATE
340 Storke Rd
Goleta, CA 93117
Phone (805) 968-9460
aTSaIrTnetaLBEar:rbearagTieschtnoelogryeCedntertrademaFrakx s(805) 968-9811
RECOMMENDED TRACE LAYOUT: FR4
SIZE DWG. NO.
REV
XQ_TraceLayout-MCPCB XQ_TraceLayout-FR4.X ± .25
A A.XX ± .10
FINAL PROTECTIVE FINISH
.X ± .25
.XX ± .10
FINAL PROTECTIVE FINISH Free Datasheet http://www.datasheet4u.com/
SCALE
X° ± 2°
SCALE 10:1
SHEET 1 OF 1


XQEAWT-00-0000-00000LEE1 (CREE)
LEDs

No Preview Available !

Click to Download PDF File for PC

INFORMATION
RY AND
C. THIS PLOT
ISCLOSED TO ANY
RITTEN CONSENT
REV
DESCRIPTION
BY DATE APP'D
xlamp xQ-e leds
D
Tape and Reel
All Cree carrier tapes conform to EIA-481D, Automated Component Handling Systems Standard.
All dimensions in mm.
Measurement tolerances unless indicated otherwise: .xx = .25 mm, .xxx = .125 mm
C
4.000
1.500
+-4..01.000 ±.1
1.75 ±.10
CATHODE SIDE
12.0
+.3
.0
2.000
1.000
ANODE SIDE
END
1.5 ±.1
8.0 ±.1
A
1.750
Cathode Side
8.000
NOMINAL
8.30
MAX
2.5 ±.1
A 3.50 ±.10
Anode Side
(denoted by + and circle)
.30 ± .10
User Feed Direction
START
1.65
1.85
B
mulative tolerance ±
5
Trailer
160 mm (min) of
empty pockets
sealed with tape
(20 pockets min.)
0.2mm
4
REFERENCE VENDOR PART NUMBER 021142
Loaded Pockets
(2,000 Lamps)
THIRD ANGLE PROJECTION
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
.XX ±
.XXX ±
X° ±
.25
.125
.5 °
FOR SHEET METAL PARTS ONLY
.X ±
.XX ±
.XXX ±
X° ±
1.5
.75
.25
.5 °
Leader
400 mm (min) ofDRAWN BY
D. CRONIN
DATE
5/31/12
CHECK emDpATtEy pockets with
4600 Silicon Drive
Durham, N.C 27703
Phone (919) 313-5300
at least 100 mmAPPROVED
DATE
Fax (919) 313-5558
TITLE
MATERIAL
sealed by taCpaerrier Tape, 1.7X1.7 XPQ
(50 empty pockets min.)
FINAL PROTECTIVE FINISH
SIZE
C
2402-00023DRAWING NO.
REV.
A
A
USUsRFeACrEFFIeNISeHd: 1.D6 irection
32
SCALE 4.000
SHEET
1
OF
1 /1
Cover Tape
Pocket Tape
13mm
7"
Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks
of Cree, Inc.
14
Free Datasheet http://www.datasheet4u.com/


XQEAWT-00-0000-00000LEE1 (CREE)
LEDs

No Preview Available !

Click to Download PDF File for PC

xlamp xQ-e leds
Packaging
The diagrams below show the packaging and labels Cree uses to ship XLamp XQ-E LEDs. XLamp XQ-E LEDs are shipped
in tape loaded on a reel. Each box contains only one reel in a moisture barrier bag.
Unpackaged Reel
Vacuum-Sealed
MVMaoociuisstuutmure-rSBeeaarBlreieadrrBraiegr Bag
Packaged Reel
CLRaEbEeBlinwCiotdheCree Bin
Lab&CeoBadlrecow,dQeiLttayhb,eLlCotr#ee Bin
Code, Qty, Reel ID
Patent Label
LLaabbeel wl iwthitChusCtormeeer Bin
CP/oNd, Qet,y,QLotyt ,#,LPoOt##
LQLCaatobybde,eel,lRwQiwettyhe,itCRlhueIseDtCloIm,rDe,ePrPeOOOOr#d#errder Code,
Label with Cree Bin
Code, Qty, Reel ID
Boxed Reel
Label with Cree Order Code,
Qty, Reel ID, PO #
Label with Cree Bin
Code, Qty, Reel ID
Patent Label
(on bottom of box)
Copyright © 2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered trademarks
of Cree, Inc.
15
Free Datasheet http://www.datasheet4u.com/




XQEAWT-00-0000-00000LEE1.pdf
Click to Download PDF File