MNA02 (Rohm)
chip capacitor networks

No Preview Available !

Click to Download PDF File for PC

www.DataSheet4U.com
Ceramic capacitors
MNA02
(1005 (0402)×2 size, chip capacitor networks)
MNA02
zFeatures
Two multi-layer ceramic capacitors are integrated on a single chip providing reduced cost and mounting space.
zQuick Reference
The design and specifications are subject to change without prior notice. Please check the most recent technical
specifications prior to placing orders or using the product. For more detail information regarding packaging style code,
please check product designation.
zHigh dielectric constant
Part No.
Size code
Temperature characteristics
code
Operating temp. range
(°C)
Rated voltage
(V)
MNA02
1005x2
(0402x2)
CN
±15%
(X5R)
25 to +85
6.3
Capacitance(pF)
1,000,000
Capacitance
tolerance
M(±20%)
Thickness
(mm)
0.8+0.05
0.10
zExternal dimensions (Unit : mm)
1.37±0.15
0.36±0.1
0.64±0.1
C1 C2
C1 =C 2
zProduct designation
Part No.
Code Product thickness Packaging specifications
K 0.8mm Paper tape(width 8 mm, pitch 4 mm)
Reel(φ180mm) : compatible with EIAJ ET-7200A
Packaging style
Reel
φ180mm(7in.)
Basic ordering unit(pcs.)
4,000
MNA 0 2 8 CN 1 0 5 M K
Rated voltage
Code Voltage
8 6.3V
Temperature characteristic code
:Refer to quick reference table.
Nominal
Capacitance tolerance
capacitance Code
tolerance
3-digit designation M
according to IEC
±20%
1/6


MNA02 (Rohm)
chip capacitor networks

No Preview Available !

Click to Download PDF File for PC

www.DataSheet4U.com
Ceramic capacitors
MNA02
zPerformance and test method
No. Items
1 Appearance and
dimensions
2 Withstanding voltage
3 Insulation resistance
4 Capacitance
Performance
Test Method
(As per JIS C 5101-1, JIS C 5101-10)
No marked defects shall be allowed As per 4.4 of JIS C 5101-1.
for appearance.
As per 4.5 of JIS C 5101-10
Dimensions shall be as specified the Using a Magnifier.
clause 4.
No dielectrical breakdown or other
damage shall be allowed.
As per 4.6 of JIS C 5101-1.
As per 4.6.4 of JIS C 5101-10
Voltage shall be applied as per Table1.
Table 1
Characteristic
Voltage
CN 250% Rated voltage
Voltage shall be applied for 1 to 5s with
50mA charging and discharging current.
Not less than 100MΩ µF
within +/−20%
As per 4.5 of JIS C 5101-1.
As per 4.6.3 of JIS C 5101-10
Measurements shall be made after
60+/−5s period of the rated voltage
applied.
As per 4.7 of JIS C 5101-1.
As per 4.6.1 of JIS C 5101-10
Measurements shall be made under the
conditions specified in Table 2.
Table 2
Characteristic Frequency Voltage
CN
1+/−0.1kHz
1+/−0.1Vrms.
5 Dielectric loss tangent
6 Temperature
characteristic
tan δ <10.0%
Applied Capacitance Temperature
voltage
range
0Vdc
Within
+/−15%
55°C~
+85°C
0Vdc
3.15
Vdc
Within
+/−10%
Within
+0/−30%
25°C~
+85°C
25°C~
+85°C
As per 4.8 of JIS C 5101-1.
As per 4.6.2 of JIS C 5101-10
Measurements shall be made under the
conditions specified in Table 2.
As per 4.24 of JIS C 5101-1.
As per 4.7 of JIS C 5101-10
If required, measurements shall be made
at a given temperature.
Measurements shall be made under the
conditions specified in Table 2.
Table 2
Characteristic Frequency Voltage
CN
1+/−0.1kHz
1+/−0.1Vrms.
7 Solderability
More than 3/4 of each end
termination shall be covered with
new solder.
As per 4.15.2 of JIS C 5101-1.
As per 4.11 of JIS C 5101-10
The solder specified in JIS Z 3282 H63A
shall be used. And the flux containing 25%
rosin and ethanol solution shall be used.
The specimens shall be immersed into the
solder at 235+/−5°C for 2+/−0.5s
So that both end terminations are
completely under solder.
2/6


MNA02 (Rohm)
chip capacitor networks

No Preview Available !

Click to Download PDF File for PC

www.DataSheet4U.com
Ceramic capacitors
MNA02
No. Items
Performance
8 Resistance Appearance Without mechanical damage.
to soldering
heat Change
rate from Within +/−7.5%
initial value
Dielectric
loss
tangent
Within specified initial value.
Insulation
resistance
Within specified initial value.
Withstanding No defects shall be allowed.
voltage
9 End termination
adherence
Without peeling or sign of
peeling shall be allowed
on the end terminations.
Test Method
(As per JIS C 5101-1, JIS C 5101-10)
As per 4.14 of JIS C 5101-1.
As per 4.10 of JIS C 5101-10
The solder specified in JIS Z 3282. H63A
shall be used.
The specimens shall be immersed into the
solder at 260+/−5°C for 5+/−0.5s so that
both end terminations are completely
under the solder.
Pre-heating at 150+/−10°C for 1 to 2min
Initial measurements prior to test shall be
performed after the thermal
Pre-conditioning specified in Remarks (1).
Final measurements shall be made after the
specimens have been left at room
temperature as per Table3.
Table 3
Characteristic
Time
CN 48+/−4 h
As per 4.13 of JIS C 5101-1.
As per 4.8 ofJIS C 5101-10
A 2N weight for 10+/−1s shall be applied
to the soldered specimens as shown by the
arrow mark in the below sketch.
Applied pressure
10 Bending
strength
Appearance Without mechanical damage.
11 Vibration
Appearance Without mechanical damage.
Change
rate from Within +/−7.5%
initial value
Dielectric
loss
tangent
Within specified initial value.
Capacitor Substrate
As per 4.35 of JIS C 5101-1.
As per 4.9 of JIS C 5101-10
Glass epoxy board with soldered
specimens shall be bent till 1mm by
1.0mm/s.
As per 4.17 of JIS C 5101-1.
The specimens shall be soldered on the
specified test jig.
Initial measurements shall be made after
the thermal pre-conditioning specified in
Remarks(1).
Final measurements shall be made after the
specimens have been left at room
temperature as per Table3.
[Condition]
Directions : 2h each X, Y and Z directions
Total : 6h
Frequency range : 10 to 55 to 10Hz(1min)
Applitude : 1.5mm
(shall not exceed acceleration196m/s2)
Table 3
Characteristic
Time
CN 48+/−4 h
3/6


MNA02 (Rohm)
chip capacitor networks

No Preview Available !

Click to Download PDF File for PC

www.DataSheet4U.com
Ceramic capacitors
MNA02
No. Items
Performance
12 Temperature Appearance Without mechanical damage.
cycling
Change
rate from Within +/−15.0%
initial value
Dielectric
loss
tangent
Within specified initial value.
Insulation
resistance
Within specified initial value.
Withstanding No defects shall be allowed.
voltage
13 Humidity
(Steady)
Appearance Without mechanical damage.
Change
rate from Within +/−25%
initial value
Dielectric
tangent
Less than 200% of initial spec.
Insulation Not less than 10M.
resistance
14 Humidity
life test
Appearance Without mechanical damage.
Change
rate from Within +/−25.0%
initial value
Dielectric
loss
tangent
Less than 200% of initial spec.
Insulation Not less than 5M.
resistance
Test Method
(As per JIS C 5101-1, JIS C 5101-10)
As per 4.16 of JIS C 5101-1
As per 4.12 of JIS C 5101-10
The specimens shall be soldered on the test
jig shown in Remarks.
Temperature cycle : 100cycles Initial
measurements prior to test shall be
performed after the thermal
per-conditioning specified in Remarks (1).
Final measurements shall be made after the
specimens have been left at room
temperature as per Table3.
Test condition
Step
Temp. (°C)
Time (min)
1 Min operating temp. 30+/−3
2 Room temp.
<− 3
3 Max operating temp. 30+/−3
4 Room temp.
<− 3
Table 3
Characteristic
Time
CN 48+/−4 h
As per 4.22 of JIS C 5101-1
As per JIS C 5101-10
Test temperature : 60+/−2°C
Relative humidity : 90 to 95%
Test time : 500 +24/−0 h
Initial measurements prior to test shall
be made after the voltage
pre-conditioning specified in
Remarks (2).
Final measurements have been left at
room temperature as per Table3.
Table 3
Characteristic
Time
CN 48+/−4 h
As per 4.22 of JIS C 5101-1
As per 4.14 of JIS C 5101-10
Test temperature : 60+/−2°C
Relative humidity : 90 to 95%
Voltage : Rated voltage
Test time : 500 +24/−0 h
Initial measurements prior to test shall
be made after the voltage
pre-conditioning specified in
Remarks (2).
Final measurements shall be made after
the specimens have been left at room
temperature as per Table3.
Table 3
Characteristic
Time
CN 48+/−4 h
4/6


MNA02 (Rohm)
chip capacitor networks

No Preview Available !

Click to Download PDF File for PC

www.DataSheet4U.com
Ceramic capacitors
MNA02
No. Items
Performance
15 Heat life
test
Appearance Without mechanical damage.
Change
rate from Within +/−25.0%
initial value
Dielectric
loss
tangent
Less than 200% of initial spec.
Insulation
resistance
Not less than 10M.
Test Method
(As per JIS C 5101-1, JIS C 5101-10)
As per 4.23 of JIS C 5101-1.
As per 4.15 of JIS C 5101-10
Test
temperature
Voltage
Test
time (h)
85°C
Rated 1000
voltage +48/−0
Initial measurements prior to test shall be
made after the voltage pre-conditioning
specified in Remarks (2).
Final measurements shall be made after
the specimens have been left at room
temperature
Table 3
Characteristic
Time
CN 48+/−4 h
[Remarks]
Pre-conditioning
If specified in test method of as per 3(Performance and test method), capacitors of CNcharacteristics
shall be pre-conditionded as follows.
(1) Thermal pre-conditioning
Prior to initial measurements, specimens shall be conditioned at a temperature of 150 0/−10°C
for a period of 1hr., and shall be allowed to stabilize at room temperature for 48+/−4h
(2) Voltage pre-conditioning
Prior to initial measurements, voltage specified as a test condition shall be applied to specimens
for a period of 1hr., and the specimens shall be allowed to stabilize at room temperature for 48+/−4h
<Test jig>
Soldering
Glass epoxy
substrate
5/6


MNA02 (Rohm)
chip capacitor networks

No Preview Available !

Click to Download PDF File for PC

www.DataSheet4U.com
Ceramic capacitors
zPackaging specifications
Taping dimensions
t
φJ
A
B
MNA02
Reel dimensions
E
D
C
Pulling direction
9.0 +−10.0
t1 F G H
K, L
Pulling direction
Symbol C D E F G H J
t t1
Dimensions
8.00
+/ −0.20
3.5
+/ −0.05
1.75
+/ −0.10
4.0
+/ −0.10
2.0
+/ −0.05
4.0
+/ −0.10
φ1.5
+0.1/ −0
0.95
+/ −0.05
1.05
MAX.
Symbol
Style
A
B
MNA02
1.30+/0.051.70+/0.05
(Unit : mm)
Label pasting
As per EIAJ ET7200A
(Unit : mm)
zElectrical characteristics curves
30
20
30
0
10
20
30
15
10
5
80 40 0 40 80 120
Fig.1 Temperature (°C)
6/6


MNA02 (Rohm)
chip capacitor networks

No Preview Available !

Click to Download PDF File for PC

www.DataSheet4U.com
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level of
reliability and the malfunction of with would directly endanger human life (such as medical instruments,
transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other
safety devices), please be sure to consult with our sales representative in advance.
About Export Control Order in Japan
Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control
Order in Japan.
In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause)
on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction.
Appendix1-Rev1.1




MNA02.pdf
Click to Download PDF File