KM10 (ME-Mebsysteme)
Force Sensor

No Preview Available !

Click to Download PDF File for PC

Force Sensor KM10
Nominal force ranges: 25N, 50N, 100N, 500N, 1000N
The KM10 is a membrane force sensor in ultra miniature design.
The force is transmitted via the universal ball joint (diameter 2.4mm, R4) in the centre of
the sensor.
The force sensor is assembled on a flat surface. The force sensor is centered on the outer
circumference, for example with 3 pins or within a 0.5 mm deep sink. The 9.8mm – 7.4mm
ring forms the sensor’s contact area. In the centre, a potting compound is visible up to a
7.4mm diameter. The inner ring is not used for centring.
To protect against lift-off, the contact area can be fixed on a flat surface with PUR lacquer.
Due to its small dimensions, a Teflon cable with an outer diameter of just 1.4mm is used.
Processing the AWG36 stranded wires requires a special tool (scalpel, Hoffmann stripper-
AWG36-26). The Teflon coating is intended exclusively for fixed installation, not for mobile
use.
A version with a central cable outlet is available as an alternative to a lateral cable outlet.
Cable type in this version is STC-31v-4RWBG, PVC, Diameter 2,2mm;
collateral cabel outlet
central cabel outlet
ME-Meßsysteme GmbH, Neuendorfstr. 18a, DE-16761 Hennigsdorf
Tel +49 (0)3302 78620 60, Fax +49 (0)3302 78620 69, info@me-systeme.de, www.me-systeme.de
1


KM10 (ME-Mebsysteme)
Force Sensor

No Preview Available !

Click to Download PDF File for PC

Dimensions
ME-Meßsysteme GmbH, Neuendorfstr. 18a, DE-16761 Hennigsdorf
2 Tel +49 (0)3302 78620 60, Fax +49 (0)3302 78620 69, info@me-systeme.de, www.me-systeme.de


KM10 (ME-Mebsysteme)
Force Sensor

No Preview Available !

Click to Download PDF File for PC

Technical Data
Measurement / Material
Design
Membrane – compression
Material
stainless steel
Dimensions
mm x mm
Ø 9,8 x 4
KM10 1kN Ø 9,8 x 4 ,5
Force tansmission / Thread
mm Kalotte Ø2,4, Radius 4
Mechanical Dat
Nominal Force (FS)
N 25, 50, 100, 500, 1000
Operation force
%FS
150
Break load
%FS
300
Deflection by FS
mm 0,08
Electrical Data
Nominal output 1)
mV/V @ FS
0,5...1,1
Zero balance
mV/V
0,1
max. supply voltage
V5
Input resistance
Ohm
350 ±40
Output resistance
Ohm
350
Insulation resistance
Ohm
>2 109
Cable: STC-36T-4 or
m3
STC-31V-4 (axial version)
Accuracy
Accuracy Class
%1
rel. linearity deviation
%FS
0,1
rel. reversal error
%FS
0,05
Temperature coefficient of the zero
signal
%FS/K
0,02
Temperature coefficient of the parameter
%RD/K
0,02
Creep Error (30 min)
%FS
0,1
Temperature
Nominal temperature range
°C -10 … +70
Working temperature range
°C -10 … +85
Storage temperature range
°C -10 … +85
Environmental protection
IP64
Abbreviation : RD: „Reading“; FS: „Full Scale“;
1) The exact nominal sensitivity is indicated in the test report;
ME-Meßsysteme GmbH, Neuendorfstr. 18a, DE-16761 Hennigsdorf
Tel +49 (0)3302 78620 60, Fax +49 (0)3302 78620 69, info@me-systeme.de, www.me-systeme.de
3


KM10 (ME-Mebsysteme)
Force Sensor

No Preview Available !

Click to Download PDF File for PC

Pin Configuration
+US positive bridge supply
-US negative bridge supply
+UD positive bridge output
-UD negative bridge output
Shield
Pressure load : positive output signal
red
black
green
white
transparent
Version: 16.02.2015
ME-Meßsysteme GmbH, Neuendorfstr. 18a, DE-16761 Hennigsdorf
4 Tel +49 (0)3302 78620 60, Fax +49 (0)3302 78620 69, info@me-systeme.de, www.me-systeme.de




KM10.pdf
Click to Download PDF File