TMP91PW10 Datasheet PDF - Toshiba


Part Number TMP91PW10
Description CMOS 16-Bit Microcontroller
Page 28 Pages

TMP91PW10 datasheet pdf
View PDF for PC
TMP91PW10 pdf
View PDF for Mobile

No Preview Available !

TOSHIBA Original CMOS 16-Bit Microcontroller
TLCS-900/L1 Series
Semiconductor Company

No Preview Available !

Thank you very much for making use of Toshiba microcomputer LSIs.
Before use this LSI, refer the section, “Points of Note and Restrictions”.
Especially, take care below cautions.
How to release the HALT mode
Usually, interrupts can release all halts status. However, the interrupts (NMI ,
INT0), which can release the HALT mode may not be able to do so if they are
input during the period CPU is shifting to the HALT mode (for about 5 clocks of
fFPH) with IDLE1 or STOP mode (IDLE2 is not applicable to this case). (In this
case, an interrupt request is kept on hold internally.)
If another interrupt is generated after it has shifted to HALT mode completely,
halt status can be released without difficultly. The priority of this interrupt is
compare with that of the interrupt kept on hold internally, and the interrupt with
higher priority is handled first followed by the other interrupt.

No Preview Available !

Document Change Notification
The purpose of this notification is to inform customers about the launch of the Pb-free version of the
device. The introduction of a Pb-free replacement affects the datasheet. Please understand that this
notification is intended as a substitute for a revision of the datasheet.
Changes to the datasheet may include the following, though not all of them may apply to this
particular device.
1. Part number
Example: TMPxxxxxxF TMPxxxxxxFG
All references to the previous part number were left unchanged in body text. The new
part number is indicated on the prelims pages (cover page and this notification).
2. Package code and package dimensions
Example: LQFP100-P-1414-0.50C LQFP100-P-1414-0.50F
All references to the previous package code and package dimensions were left unchanged
in body text. The new ones are indicated on the prelims pages.
3. Addition of notes on lead solderability
Now that the device is Pb-free, notes on lead solderability have been added.
The previous (obsolete) provision might be left unchanged on page 1 of body text. A new
replacement is included on the next page.
5. Publication date of the datasheet
The publication date at the lower right corner of the prelims pages applies to the new
I 2008-02-20

No Preview Available !

1. Part number
Previous Part Number (in Body Text)
New Part Number
2. Package code and dimensions
Previous Package Code (in Body Text)
New Package Code
*: For the dimensions of the new package, see the attached Package Dimensions diagram.
3. Addition of notes on lead solderability
The following solderability test is conducted on the new device.
Solderability of lead free products
Test Parameter
Test Condition
Use of Sn-37Pb solder Bath
Solder bath temperature = 230°C, Dipping time = 5 seconds
The number of times = one, Use of R-type flux
Use of Sn-3.0Ag-0.5Cu solder bath
Solder bath temperature = 245°C, Dipping time = 5 seconds
The number of times = one, Use of R-type flux
(use of lead free)
Solderability rate until forming
The following replaces the “RESTRICTIONS ON PRODUCT USE” on page 1 of body text.
The information contained herein is subject to change without notice.
TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor
devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical
stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety
in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such
TOSHIBA products could cause loss of human life, bodily injury or damage to property.
In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as
set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and
conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability
Handbook” etc.
The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer,
personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These
TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high
quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury
(“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship
instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical
instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall
be made at the customer’s own risk.
The products described in this document shall not be used or embedded to any downstream products of which
manufacture, use and/or sale are prohibited under any applicable laws and regulations.
The information contained herein is presented only as a guide for the applications of our products. No responsibility
is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its
use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third
Please contact your sales representative for product-by-product details in this document regarding RoHS
compatibility. Please use these products in this document in compliance with all applicable laws and regulations that
regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring
as a result of noncompliance with applicable laws and regulations.
For a discussion of how the reliability of microcontrollers can be predicted, please refer to Section 1.3 of the chapter
entitled Quality and Reliability Assurance/Handling Precautions.
5. Publication date of the datasheet
The publication date of this datasheet is printed at the lower right corner of this notification.
II 2008-02-20

TMP91PW10 datasheet pdf
Download PDF
TMP91PW10 pdf
View PDF for Mobile

Similiar Datasheets : TMP91PW10 TMP91PW10F TMP91PW10FG TMP91PW11 TMP91PW11F TMP91PW12 TMP91PW12F

Index :   0   1   2   3   4   5   6   7   8   9   A   B   C   D   E   F   G   H   I   J   K   L   M   N   O   P   Q   R   S   T   U   V   W   X   Y   Z   

This is a individually operated, non profit site. If this site is good enough to show, please introduce this site to others.
Since 2010   ::   HOME   ::   Privacy Policy + Contact