SPI3012 Datasheet PDF - Superworld Electronics

www.Datasheet-PDF.com

SPI3012
Superworld Electronics

Part Number SPI3012
Description SMD POWER INDUCTORS
Page 5 Pages


SPI3012 datasheet pdf
Download PDF
SPI3012 pdf
View PDF for Mobile


No Preview Available !

SMD POWER INDUCTORS (PRELIMINARY) SPI3012 SERIES
1. PART NO. EXPRESSION :
SPI3012-1R0NZF-
(a) (b)
(c) (d)(e)(f) (g)
(a) Series code
(b) Dimension code
(c) Inductance code : 1R0 = 1.0uH
(d) Tolerance code : M = ±20%, N = ±30%
(e) Z : Standard part
(f) F : RoHS Compliant
(g) 11 ~ 99 : Internal controlled number
2. CONFIGURATION & DIMENSIONS :
A EDE
E
Marking
3.2
3.4
OR
1.4
0.6
Recommended PCB Pattern
Unit:m/m
ABCDEF G
3.0±0.2 3.0±0.3 1.2 Max. 1.5 Typ 0.76 Typ 1.2 Typ 0.7 Typ
3. MATERIALS :
(a) Core : Ferrite
(b) Wire : Polyurethane Enamelled Copper Wire
(c) Terminal Clip : C5191
(d) Adhesive : Epoxy
(e) Ink : 70000-00101
www.DataSheet4U.com
NOTE : Specifications subject to change without notice. Please check our website for latest information.
SUPERWORLD ELECTRONICS
(S)
PTE
23.09.2010
LTD
PG. 1



No Preview Available !

SMD POWER INDUCTORS (PRELIMINARY) SPI3012 SERIES
4. GENERAL SPECIFICATION :
a) IDC1 : Based on inductance change (ǻL/Lo: <30%) @ ambient temp. 25°C
b) IDC2 : Based on temperature rise (ǻT: 40°C Typ.)
c) Rated Current : IDC1 or IDC2, whichever value is lower
d) Storage temp. : -40°C to +105°C
e) Operating temp. : -40°C to +105°C ( include self temp. rise )
f) Resistance to solder heat : 260°C 10secs
5. ELECTRICAL CHARACTERISTICS :
Part No.
Inductance
( uH )
SPI3012-1R0NZF-
SPI3012-1R2NZF-
SPI3012-1R5NZF-
SPI3012-2R2NZF-
SPI3012-3R3NZF-
SPI3012-3R9NZF-
SPI3012-4R7MZF-
SPI3012-5R6MZF-
SPI3012-6R8MZF-
SPI3012-8R2MZF-
SPI3012-100MZF-
SPI3012-120MZF-
SPI3012-150MZF-
SPI3012-220MZF-
1.0±30%
1.2±30%
1.5±30%
2.2±30%
3.3±30%
3.9±30%
4.7±20%
5.6±20%
6.8±20%
8.2±30%
10±20%
12±20%
15±20%
22±20%
Test
Frequency
( Hz )
0.1V/100K
0.1V/100K
0.1V/100K
0.1V/100K
0.1V/100K
0.1V/100K
0.1V/100K
0.1V/100K
0.1V/100K
0.1V/100K
0.1V/100K
0.1V/100K
0.1V/100K
0.1V/100K
RDC
( mȍ )
±20%
55
63
75
110
150
180
210
270
330
380
410
550
680
950
IDC1
(A)
1.50
1.40
1.30
1.00
0.87
0.82
0.75
0.65
0.60
0.55
0.50
0.45
0.40
0.35
IDC2
(A)
1.80
1.65
1.50
1.30
1.10
1.00
0.90
0.80
0.70
0.65
0.60
0.55
0.45
0.35
Marking
A
B
C
E
G
H
I
J
K
L
M
N
O
Q
www.DataSheet4U.com
NOTE : Specifications subject to change without notice. Please check our website for latest information.
SUPERWORLD ELECTRONICS
(S)
PTE
23.09.2010
LTD
PG. 2



No Preview Available !

SMD POWER INDUCTORS (PRELIMINARY) SPI3012 SERIES
6. RELIABILITY & TEST CONDITION :
ITEM
Mechanical
Substrate bending
PERFORMANCE
ǻL/Lo<±10%
There shall be no mechanical damage or
electrical damage.
TEST CONDITION
The sample shall be soldered onto the printed circuit board
in figure 1 and a load applied until the figure in the arrow
direction is made approximately 3mm.(keep time 30 secs)
100
50
Ø4.5
t = 1.6
Vibration
Solderability
ǻL/Lo<±10%
There shall be no mechanical damage.
New solder
More than 90%
Resistance to Soldering heat
(reflow soldering)
There shall be no damage or problems.
20 30
30
20 Bending test board
R5
45±2
PRESSURE ROD figure-1
45±2
20
10
R340
The sample shall be soldered onto the printed circuit board
and when a vibration having an amplitude of 1.52mm and
a frequency of from 10 to 55Hz/1 minute repeated should
be applied to the 3 directions (X,Y,Z) for 2 hours each.
(A total of 6 hours)
Flux (rosin, isopropyl alcohol{JIS-K-1522}) shall be coated
over the whole of the sample before hard, the sample shall
then be preheated for about 2 minutes in a temperature of
130~150°C and after it has been immersed to a depth 0.5mm
below for 3±0.2 seconds fully in molten solder M705 with
a temperature of 245±5°C.
More than 90% of the electrode sections shall be cowered
with new solder smoothly when the sample is taken out of
the solder bath.
Soldering
300 (Peak temperature 260±3°C 10sec)
250
200
30 sec Min.
(230°C Max.)
150 Pre-heating
100
150~
50 180°C
Slow cooling
(Stored at room
temperature)
2 min.
10 2 min. or more
sec
The specimen shall be passed through the reflow oven with
the condition shown in the above profile for 1 time.
The specimen shall be stored at standard atmospheric
conditions for 1 hour, after which the measurement shall
be made.
www.DataSheet4U.com
NOTE : Specifications subject to change without notice. Please check our website for latest information.
23.09.2010
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 3



No Preview Available !

SMD POWER INDUCTORS (PRELIMINARY) SPI3012 SERIES
6. RELIABILITY & TEST CONDITION :
ITEM
Electrical Characteristics Test
Dielectric withstand voltage
PERFORMANCE
There shall be no damage or problems.
Temperature characteristics
ǻL/L20°C<±10%
0~2000 ppm/°C
High temperature storage
ǻL/Lo<±10%
There shall be no mechanical damage.
TEST CONDITION
AC 100V voltage shall be applied for 1 minute across the
top surface and the terminal of this sample
The test shall be performed after the sample has stabilized
in an ambient temperature of -20 to +85°C,and the value
calculated based on the value applicable in a normal
temperature and normal humidity shall be ǻL/L20°C<±10%.
The sample shall be left for 96±4 hours in an atmosphere
with a temperature of 85±2°C and a normal humidity.
Upon completion of the measurement shall be made after
the sample has been left in a normal temperature and
normal humidity for 1 hour.
Low temperature storage
Change of temperature
Moisture storage
ǻL/Lo<±10%
There shall be no mechanical damage.
The sample shall be left for 96±4 hours in an atmosphere
with a temperature of -25±3°C.
Upon completion of the test, the measurement shall be
made after the sample has been left in a normal temperature
and normal humidity for 1 hour.
ǻL/Lo<±10%
There shall be no other damage of problems
The sample shall be subject to 5 continuous cycles, such as
shown in the table 2 below and then it shall be subjected to
standard atmospheric conditions for 1 hour, after which
measurement shall be made.
Temperature
Duration
-25±3°C
1 (Thermostat No.1) 30 min.
Standard
5 sec. or less
2 atmospheric No.1ĺNo.2
85±2°C
3 (Thermostat No.2) 30 min.
4
Standard
atmospheric
5 sec. or less
No.2ĺNo.1
ǻL/Lo<±10%
There shall be no mechanical damage.
The sample shall be left for 96±4 hours in a temperature of
40±2°C and a humidity(RH) of 90~95%.
Upon completion of the test, the measurement shall be
made after the sample has been left in a normal temperature
and normal humidity more than 1 hour.
www.DataSheet4U.com
NOTE : Specifications subject to change without notice. Please check our website for latest information.
23.09.2010
SUPERWORLD ELECTRONICS (S) PTE LTD
PG. 4



SPI3012 datasheet pdf
Download PDF
SPI3012 pdf
View PDF for Mobile


Related : Start with SPI301 Part Numbers by
SPI3012 SMD POWER INDUCTORS SPI3012
Superworld Electronics
SPI3012 pdf
SPI3015 SMD POWER INDUCTORS SPI3015
Superworld Electronics
SPI3015 pdf

Index :   0   1   2   3   4   5   6   7   8   9   A   B   C   D   E   F   G   H   I   J   K   L   M   N   O   P   Q   R   S   T   U   V   W   X   Y   Z   

This is a individually operated, non profit site. If this site is good enough to show, please introduce this site to others.
Since 2010   ::   HOME   ::   Contact