Freescale SMeBmC1ic39o0n1ductor, Inc.
ARCHIVED BY FREESCALE SEMICONDUCPLTAOSTRIC, PINACCK.A2G0E05
PIN 1 IDENTIFIER
D IN THIS ZONE
0.10 M C A–B D
(SEE NOTE 7)
4X q 1
4X q 1
1. DIMENSIONS ARE IN MILLIMETERS.
2. INTERPRET DIMENSIONS AND TOLERANCES PER
ASME Y14.5M, 1994.
3. DIMENSION D DOES NOT INCLUDE MOLD FLASH,
PROTRUSIONS OR GATE BURRS. MOLD FLASH,
PROTRUSIONS OR GATE BURRS SHALL NOT
EXCEED 0.15mm PER END. DIMENSION E1 DOES
NOT INCLUDE INTERLEAD FLASH OR
PROTRUSION. INTERLEAD FLASH OR PROTRUSION
SHALL NOT EXCEED 0.15mm PER SIDE.
4. DIMENSIONS D AND E1 ARE DETERMINED AT THE
OUTMOST EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS,
GATE BURRS AND INTERLEAD FLASH, BUT
INCLUDING ANY MISMATCH BETWEEN THE TOP
AND BOTTOM OF PLASTIC BODY.
5. DATUMS A, B AND D TO BE DETERMINED 0.10mm
FROM THE LEAD TIP.
6. TERMINAL NUMBERS ARE SHOWN FOR
7. THESE DIMENSIONS APPLY TO THE FLAT SECTION
OF THE LEAD BETWEEN 0.08mm AND 0.15mm FROM
THE LEAD TIP.
DIM MIN MAX
A ––– 1.10
A1 0.00 0.10
A2 0.80 1.00
b 0.25 0.40
b1 0.25 0.35
B 0.55 0.70
B1 0.55 0.65
c 0.10 0.25
c1 0.08 0.20
D 2.00 BSC
E 2.10 BSC
E1 1.25 BSC
e1 1.30 BSC
e2 0.65 BSC
e3 1.15 BSC
e4 0.50 BSC
L 0.26 0.46
L1 0.425 REF
L2 0.15 BSC
q 0 _ 8_
q1 4 _ 10_
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
How to reach us:
USA / EUROPE / Locations Not Listed: Motorola Literature Distribution;
JAPAN: Motorola Japan Ltd.; SPS, Technical Information Center, 3–20–1,
P.O. Box 5405, Denver, Colorado 80217. 1–303–675–2140 or 1–800–441–2447 Minami–Azabu. Minato–ku, Tokyo 106–8573 Japan. 81–3–3440–3569
Technical Information Center: 1–800–521–6274
HOME PAGE: http://www.motorola.com/semiconductors/
ASIA / PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Centre,
2, Dai King Street, Tai Po Industrial Estate, Tai Po, N.T., Hong Kong.
4 ◊For More Information On This PMrOoTdOuRcOt,LA WIRELESS SEMICMOBNCD1U39C0T1POPR/D
Go to: www.freescale.comSOLUTIONS – RF AND IF DEVICE DATA