JTMP91C016S Datasheet PDF - Toshiba


www.Datasheet-PDF.com

JTMP91C016S
Toshiba

Part Number JTMP91C016S
Description CMOS 16-Bit Microcontroller
Page 30 Pages

JTMP91C016S datasheet pdf
View PDF for PC
JTMP91C016S pdf
View PDF for Mobile


No Preview Available !

TOSHIBA Original CMOS 16-Bit Microcontroller
TLCS-900/L1 Series
TMP91C016FG
JTMP91C016S
Semiconductor Company



No Preview Available !

Preface
Thank you very much for making use of Toshiba microcomputer LSIs.
Before use this LSI, refer the section, “Points of Note and Restrictions”.
Especially, take care below cautions.
**CAUTION**
How to release the HALT mode
Usually, interrupts can release all halts status. However, the interrupts = (NMI ,
INT0 to INT3, INTRTC, INTALM0 to INTALM4, INTKEY, INTVLD0 to INTVLD2),
which can release the HALT mode may not be able to do so if they are input
during the period CPU is shifting to the HALT mode (for about 5 clocks of fFPH)
with IDLE1 or STOP mode (IDLE2 is not applicable to this case). (In this case, an
interrupt request is kept on hold internally.)
If another interrupt is generated after it has shifted to HALT mode completely,
halt status can be released without difficultly. The priority of this interrupt is
compare with that of the interrupt kept on hold internally, and the interrupt with
higher priority is handled first followed by the other interrupt.



No Preview Available !

TMP91C016
CMOS 16-Bit Microcontrollers
TMP91C016FG/JTMP91C016S
1. Outline and Features
TMP91C016 is a high-speed 16-bit microcontroller designed for the control of various mid- to
large-scale equipment.
TMP91C016FG comes in a 100-pin flat package. JTMP91C016S is a 100-pad chip product.
Listed below are the features.
(1) High-speed 16-bit CPU (900/L1 CPU)
Instruction mnemonics are upward compatible with TLCS-90/900
16 Mbytes of linear address space
General-purpose registers and register banks
16-bit multiplication and division instructions; bit transfer and arithmetic instructions
Micro DMA: 4 channels (592ns/ 2bytes at 27MHz)
(2) Minimum instruction execution time: 148 ns (at 27 MHz)
RESTRICTIONS ON PRODUCT USE
20070701-EN
The information contained herein is subject to change without notice.
TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor
devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical
stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety
in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such
TOSHIBA products could cause loss of human life, bodily injury or damage to property.
In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as
set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and
conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability
Handbook” etc.
The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer,
personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These
TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high
quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury
(“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship
instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical
instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall
be made at the customer’s own risk.
The products described in this document shall not be used or embedded to any downstream products of which
manufacture, use and/or sale are prohibited under any applicable laws and regulations.
The information contained herein is presented only as a guide for the applications of our products. No responsibility
is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its
use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third
parties.
Please contact your sales representative for product-by-product details in this document regarding RoHS
compatibility. Please use these products in this document in compliance with all applicable laws and regulations
that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses
occurring as a result of noncompliance with applicable laws and regulations.
For a discussion of how the reliability of microcontrollers can be predicted, please refer to Section 1.3 of the chapter
entitled Quality and Reliability Assurance/Handling Precautions.
91C016-1
2008-02-20



No Preview Available !

TMP91C016
(3) Built-in RAM: None
Built-in ROM: None
(4) External memory expansion
Expandable up to 105 Mbytes (Shared program/data area)
Can simultaneously support 8-/16-bit width external data bus: Dynamic data bus sizing
Separate bus system
(5) 8-bit timers: 4 channels
(6) General-purpose serial interface: 2 channels
Channel 0
UART mode
IrDA Ver.1.0 (115.2 kbps) mode selectable
Channel 1
UART mode
Synchronous mode selectable
(7) LCD controller
Adapt to both Shift register type and Built-in RAM type LCD driver
(8) Timer for real time clock (RTC)
Based on TC8521A
(9) Key-on wakeup (Interrupt key input)
(10) Watchdog timer
(11) Melody/alarm generator
Melody: Output of clock 4 to 5461 Hz
Alarm: Output of the 8 kinds of alarm pattern
Output of the 5 kinds of interval interrupt
(12) Chip select/wait controller: 4 channels
(13) MMU
Expandable up to 105 Mbytes (4 local area/8 bank method)
(14) Display data reciprocal conversion function between the vertical and horizontal (8 × 8)
(15) Interrupts: 40 interrupts
9 CPU interrupts: Software interrupt instruction and illegal instruction
25 internal interrupts: 7 priority levels are selectable
9 external interrupts: 7 priority levels are selectable
(among 4 interrupts are selectable edge mode)
(16) Input/output ports: 31 pins (at External 16-bit data bus memory)
(17) Standby function
Three HALT modes: IDLE2 (Programmable), IDLE1 and STOP
(18) DRAM controller
2CAS mode
(19) Voltage compare circuit: 3 channels
91C016-2
2008-02-20




JTMP91C016S datasheet pdf
Download PDF
JTMP91C016S pdf
View PDF for Mobile


Similiar Datasheets : JTMP91C016S

Index :   0   1   2   3   4   5   6   7   8   9   A   B   C   D   E   F   G   H   I   J   K   L   M   N   O   P   Q   R   S   T   U   V   W   X   Y   Z   

This is a individually operated, non profit site. If this site is good enough to show, please introduce this site to others.
Since 2010   ::   HOME   ::   Privacy Policy + Contact