Static Electrical Characteristics
Tj=-40°C..150°C, Vcc=6..18V (unless otherwise specified)
Symbol Parameter
Min. Typ. Max. Units
Vcc op.
Operating voltage range
5.8 35
V
Rds(on)
ON state resistance Tj=25°C
ON state resistance Tj=150°C (2)
4.8 5.8
7.5 9
m
Icc off
Iout off
Supply leakage current
Output leakage current
1
1
3
3
µA
Iin on
Input current when device on
1 2.7 6
mA
V clamp
Vcc to Vout clamp voltage
37 39 44
Vih(1)
High level Input threshold voltage
4.5 5.4 6.2
V
Vil(1)
Low level Input threshold voltage
4 5 5.8
Rds(on) rev Reverse On state resistance Tj=25°C
6
8 m
Vf
Forward body diode voltage Tj=25°C
0.8 0.9
Forward body diode voltage Tj=125°C 0.6 0.8
V
Rin Input resistor
115 200 300
(1) Input thresholds are measured directly between the input pin and the tab.
(2) Guaranteed by design
Test Conditions
Ids=10A
Vin=Vcc=14V,Vifb=Vgnd
Vout=Vgnd, Tj=25°C
Vcc-Vin=14V
Id=20mA
Isd=10A, Vin-Vcc>8V
If=10A
Built-in resistor
Switching Electrical Characteristics
Vcc=14V, Resistive load=1, Tj=25°C
Symbol Parameter
Tdon
Turn on delay time
Tr Rise time from 20% to 80% of Vcc
Tdoff
Turn off delay time
Tf Fall time from 80% to 20% of Vcc
Min.
20
15
20
15
Typ.
50
35
100
35
Max.
150
100
250
100
Units
µs
Test Conditions
See fig. 1
Protection Characteristics
Tj=-40°C..150°C, Vcc=6..18V (unless otherwise specified)
Symbol Parameter
Tsd Over temperature threshold(2)
Isd Over-current shutdown
I fault
Ifb after an over-current or an over-
temperature (latched)
OV Over-voltage protection
Psd rst
Time to reset Psd
Psd_UV
Time to shutdown when Vcc-Out=UV (3)
(3) See explanation page 8
Min.
150
65
15
18
12
0.3
Typ.
165
90
20
20
26
0.7
Max.
120
27
22
60
2
Units
°C
A
mA
V
ms
Test Conditions
See fig. 3
Vcc-Vin
Current Sensing Characteristics
Tj=-40°C..150°C, Vcc=6..18V (unless otherwise specified), Vcc-Vifb>3.5V
Symbol Parameter
Min. Typ. Max. Units
Ratio
I load / Ifb current ratio
5000 6300 7600
Ratio_Cold
Ratio_Hot
I offset
Ifb leakage
Ratio drift between 25°C to -40°C
Ratio drift between 25°C to 125°C
Load current offset
Ifb leakage current
-6.6
-1.6
-0.15
0
-2.2
3
0
0.5
2.1
7.7
0.15
25
%
A
µA
Test Conditions
Iload=60A at Vcc=14V,
Iload=30A at Vcc=6V,
after 1.5ms,See page 7
Ratio@-40°/Ratio@25°
Ratio@125°/Ratio@25°
After 1.5ms
Iout=0A, Vcc-Vin=14V
4 www.irf.com
© 2015 International Rectifier
Submit Datasheet Feedback
June 23, 2015