AT24C32A Datasheet PDF - ATMEL

www.Datasheet-PDF.com

AT24C32A
ATMEL

Part Number AT24C32A
Description Two-wire Serial EEPROM
Page 22 Pages


AT24C32A datasheet pdf
Download PDF
AT24C32A pdf
View PDF for Mobile

No Preview Available !

Features
Low-Voltage and Standard-Voltage Operation
– 2.7 (VCC = 2.7V to 5.5V)
– 1.8 (VCC = 1.8V to 5.5V)
Low-Power Devices (ISB = 6 µA @ 5.5V) Available
Internally Organized 4096 x 8, 8192 x 8
Two-wire Serial Interface
Schmitt Trigger, Filtered Inputs for Noise Suppression
Bidirectional Data Transfer Protocol
400 kHz (1.8V, 2.5V, 2.7V, 5V) Compatibility
Write Protect Pin for Hardware Data Protection
32-byte Page Write Mode (Partial Page Writes Allowed)
Self-timed Write Cycle (5 ms Max)
High Reliability
– Endurance: 1 Million Write Cycles
– Data Retention: 100 Years
Automotive Devices Available
8-lead JEDEC PDIP, 8-lead JEDEC SOIC, 8-lead EIAJ SOIC, 8-lead Mini-MAP (MLP 2x3)
and 8-lead TSSOP Packages
Lead-free/Halogen-free
Die Sales: Wafer Form, Waffle Pack, and Bumped Wafers
Description
The AT24C32A/64A provides 32,768/65,536 bits of serial electrically erasable and
programmable read only memory (EEPROM) organized as 4096/8192 words of 8 bits
each. The device’s cascadable feature allows up to 8 devices to share a common two-
wire bus. The device is optimized for use in many industrial and commercial applica-
tions where low power and low voltage operation are essential. The AT24C32A/64A is
available in space saving 8-lead JEDEC PDIP, 8-lead JEDEC SOIC, 8-lead EIAJ
SOIC, 8-lead Mini-MAP (MLP 2x3) and 8-lead TSSOP packages and is accessed via
a 2-wire serial interface. In addition, the entire family is available in 2.7V (2.7V to 5.5V)
and 1.8V (1.8V to 5.5V) versions.
Two-wire
Serial EEPROM
32K (4096 x 8)
64K (8192 x 8)
AT24C32A(1)
AT24C64A(2)
Notes: 1. Not recommended for
new design; please
refer to AT24C32C.
2. Not recommended for
new design; please
refer to AT24C64C.
Table 1. Pin Configuration
Pin Name Function
A0 – A2
Address Inputs
SDA
Serial Data
SCL Serial Clock Input
WP Write Protect
8-lead SOIC
8-lead Mini-MAP (MLP 2x3)
A0
A1
A2
GND
1
2
3
4
8 VCC
7 WP
6 SCL
5 SDA
VCC
WP
SCL
SDA
8
7
6
5
1 A0
2 A1
3 A2
4 GND
Bottom View
8-lead TSSOP
A0
A1
A2
GND
1
2
3
4
8 VCC
7 WP
6 SCL
5 SDA
8-lead PDIP
A0
A1
A2
GND
1
2
3
4
8 VCC
7 WP
6 SCL
5 SDA
3054T–SEEPR–1/07
1



No Preview Available !

Absolute Maximum Ratings*
Operating Temperature..................................–55°C to +125°C
Storage Temperature .....................................–65°C to +150°C
Voltage on Any Pin
with Respect to Ground .................................... –1.0V to +7.0V
Maximum Operating Voltage .......................................... 6.25V
DC Output Current........................................................ 5.0 mA
Figure 1. Block Diagram
*NOTICE:
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent dam-
age to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect
device reliability.
2 AT24C32A/64A
3054T–SEEPR–1/07



No Preview Available !

AT24C32A/64A
Pin Description
SERIAL CLOCK (SCL): The SCL input is used to positive edge clock data into each
EEPROM device and negative edge clock data out of each device.
SERIAL DATA (SDA): The SDA pin is bidirectional for serial data transfer. This pin is
open-drain driven and may be wire-ORed with any number of other open-drain or open
collector devices.
DEVICE/ADDRESSES (A2, A1, A0): The A2, A1 and A0 pins are device address inputs
that are hardwired or left not connected for hardware compatibility with other AT24Cxx
devices. When the pins are hardwired, as many as eight 32K/64K devices may be
addressed on a single bus system (device addressing is discussed in detail under the
Device Addressing section). If the pins are left floating, the A2, A1 and A0 pins will be
internally pulled down to GND if the capacitive coupling to the circuit board VCC plane is
<3 pF. If coupling is >3 pF, Atmel recommends connecting the address pins to GND.
WRITE PROTECT (WP): The write protect input, when connected to GND, allows nor-
mal write operations. When WP is connected high to VCC, all write operations to the
memory are inhibited. If the pin is left floating, the WP pin will be internally pulled down
to GND if the capacitive coupling to the circuit board VCC plane is <3 pF. If coupling is
>3 pF, Atmel recommends connecting the pin to GND. Switching WP to VCC prior to a
write operation creates a software write protect function.
Memory Organization AT24C32A/64A, 32K/64K SERIAL EEPROM: The 32K/64K is internally organized as
128/256 pages of 32 bytes each. Random word addressing requires a 12/13-bit data
word address.
3054T–SEEPR–1/07
3



No Preview Available !

Table 2. Pin Capacitance(1)
Applicable over recommended operating range from TA = 25°C, f = 1.0 MHz, VCC = +1.8V
Symbol Test Condition
Max
CI/O
CIN
Note:
Input/Output Capacitance (SDA)
Input Capacitance (A0, A1, A2, SCL)
1. This parameter is characterized and is not 100% tested.
8
6
Units
pF
pF
Conditions
VI/O = 0V
VIN = 0V
Table 3. DC Characteristics
Applicable over recommended operating range from: TAI = 40°C to +85°C, VCC = +1.8V to +5.5V, VCC = +1.8V to +5.5V
(unless otherwise noted)
Symbol Parameter
Test Condition
Min Typ Max Units
VCC1
Supply Voltage
1.8 5.5 V
VCC2
Supply Voltage
2.5 5.5 V
VCC3
Supply Voltage
2.7 5.5 V
VCC4
Supply Voltage
4.5 5.5 V
ICC1
Supply Current
VCC = 5.0V
READ at 400 kHz
0.4 1.0 mA
ICC2
Supply Current
VCC = 5.0V
WRITE at 400 kHz
2.0 3.0 mA
ISB1
Standby Current
(1.8V option)
VCC = 1.8V
VIN = VCC or VSS
1.0 µA
ISB2
Standby Current
(2.5V option)
VCC = 2.5V
VIN = VCC or VSS
2.0 µA
ISB3
Standby Current
(2.7V option)
VCC = 2.7V
VIN = VCC or VSS
2.0 µA
ISB4
Standby Current
(5V option)
VCC = 4.5 - 5.5V VIN = VCC or VSS
6.0 µA
ILI
Input Leakage
Current
VIN = VCC or VSS
0.10 3.0
µA
ILO
Output Leakage
Current
VOUT = VCC or VSS
0.05 3.0
µA
VIL(1)
VIH(1)
VOL2
VOL1
Note:
Input Low Level
Input High Level
Output Low Level
VCC = 3.0V
IOL = 2.1 mA
Output Low Level
VCC = 1.8V
IOL = 0.15 mA
1. VIL min and VIH max are reference only and are not tested.
–0.6
VCC x 0.7
VCC x 0.3
VCC + 0.5
0.4
0.2
V
V
V
V
4 AT24C32A/64A
3054T–SEEPR–1/07



AT24C32A datasheet pdf
Download PDF
AT24C32A pdf
View PDF for Mobile


Related : Start with AT24C32 Part Numbers by
AT24C32 2-Wire Serial EEPROM AT24C32
ATMEL Corporation
AT24C32 pdf
AT24C32A Two-wire Serial EEPROM AT24C32A
ATMEL
AT24C32A pdf
AT24C32C 2-Wire Serial EEPROM AT24C32C
ATMEL Corporation
AT24C32C pdf
AT24C32D I2C-Compatible (2-Wire) Serial EEPROM AT24C32D
ATMEL
AT24C32D pdf

Index :   0   1   2   3   4   5   6   7   8   9   A   B   C   D   E   F   G   H   I   J   K   L   M   N   O   P   Q   R   S   T   U   V   W   X   Y   Z   

This is a individually operated, non profit site. If this site is good enough to show, please introduce this site to others.
Since 2010   ::   HOME   ::   Contact