AOL1206 Datasheet PDF - Alpha & Omega Semiconductors

www.Datasheet-PDF.com

AOL1206
Alpha & Omega Semiconductors

Part Number AOL1206
Description 30V N-Channel MOSFET
Page 6 Pages


AOL1206 datasheet pdf
View PDF for PC
AOL1206 pdf
View PDF for Mobile


No Preview Available !

AOL1206
30V N-Channel MOSFET
General Description
Product Summary
The AOL1206 uses trench MOSFET technology that is
uniquely optimized to provide the most efficient high
frequency switching performance.Power losses are
minimized due to an extremely low combination of RDS(ON)
and Crss.In addition,switching behavior is well controlled
with a "Schottky style" soft recovery body diode.
VDS
ID (at VGS=10V)
RDS(ON) (at VGS=10V)
RDS(ON) (at VGS = 4.5V)
100% UIS Tested
100% Rg Tested
30V
54A
< 6m:
< 8.5m:
UltraSO-8TM
Top View
Bottom View
D
G
S
S
G
G
Absolute Maximum Ratings TA=25°C unless otherwise noted
Parameter
Symbol
Drain-Source Voltage
VDS
Gate-Source Voltage
VGS
Continuous Drain
TC=25°C
Current G
TC=100°C
Pulsed Drain Current C
ID
IDM
Continuous Drain
TA=25°C
Current
TA=70°C
Avalanche Current C
Avalanche energy L=0.1mH C
IDSM
IAS, IAR
EAS, EAR
TC=25°C
Power Dissipation B TC=100°C
PD
TA=25°C
Power Dissipation A TA=70°C
PDSM
Junction and Storage Temperature Range
TJ, TSTG
Maximum
30
±20
54
42
250
16
13
30
45
62
31
2.7
1.7
-55 to 175
Thermal Characteristics
Parameter
Maximum Junction-to-Ambient A
Maximum Junction-to-Ambient A D
Maximum Junction-to-Case
t ” 10s
Steady-State
Steady-State
Symbol
RTJA
RTJC
Typ
16
38
2
Max
20
46
2.4
Rev0 : Feb 2010
www.aosmd.com
D
S
Units
V
V
A
A
A
mJ
W
W
°C
Units
°C/W
°C/W
°C/W
Page 1 of 6



No Preview Available !

AOL1206
Electrical Characteristics (TJ=25°C unless otherwise noted)
Symbol
Parameter
Conditions
Min Typ Max Units
STATIC PARAMETERS
BVDSS Drain-Source Breakdown Voltage
ID=250PA, VGS=0V
30
V
IDSS Zero Gate Voltage Drain Current
VDS=30V, VGS=0V
TJ=55°C
1
PA
5
IGSS Gate-Body leakage current
VDS=0V, VGS= ±20V
100 nA
VGS(th) Gate Threshold Voltage
VDS=VGS ID=250PA
1.3 1.8 2.3
V
ID(ON)
On state drain current
VGS=10V, VDS=5V
250
A
RDS(ON) Static Drain-Source On-Resistance
VGS=10V, ID=20A
TJ=125°C
56
m:
7.4 9
VGS=4.5V, ID=15A
6.8 8.5 m:
gFS Forward Transconductance
VDS=5V, ID=20A
70 S
VSD Diode Forward Voltage
IS=1A,VGS=0V
IS Maximum Body-Diode Continuous CurrentG
0.7 1
54
V
A
DYNAMIC PARAMETERS
Ciss Input Capacitance
Coss Output Capacitance
Crss Reverse Transfer Capacitance
Rg Gate resistance
VGS=0V, VDS=15V, f=1MHz
VGS=0V, VDS=0V, f=1MHz
1110
350
32
0.4
1390
510
53
0.9
1670
670
90
1.5
pF
pF
pF
:
SWITCHING PARAMETERS
Qg(10V) Total Gate Charge
15.5 19.6 23.5 nC
Qg(4.5V) Total Gate Charge
Qgs Gate Source Charge
VGS=10V, VDS=15V, ID=20A
7 8.7 10.5 nC
2.8 3.6 4.5 nC
Qgd Gate Drain Charge
1.8 3 4.2 nC
tD(on)
Turn-On DelayTime
6 ns
tr Turn-On Rise Time
VGS=10V, VDS=15V, RL=0.75:,
2
ns
tD(off)
Turn-Off DelayTime
RGEN=3:
20 ns
tf Turn-Off Fall Time
3.5 ns
trr Body Diode Reverse Recovery Time IF=20A, dI/dt=500A/Ps
12 15 18 ns
Qrr Body Diode Reverse Recovery Charge IF=20A, dI/dt=500A/Ps
30 37 45 nC
A. The value of RTJA is measured with the device mounted on 1in2 FR-4 board with 2oz. Copper, in a still air environment with TA =25°C. The
Power dissipation PDSM is based on R TJA and the maximum allowed junction temperature of 150°C. The value in any given application depends on
the user's specific board design, and the maximum temperature of 175°C may be used if the PCB allows it.
B. The power dissipation PD is based on TJ(MAX)=175°C, using junction-to-case thermal resistance, and is more useful in setting the upper
dissipation limit for cases where additional heatsinking is used.
C. Repetitive rating, pulse width limited by junction temperature TJ(MAX)=175°C. Ratings are based on low frequency and duty cycles to keep initial
TJ =25°C.
D. The RTJA is the sum of the thermal impedence from junction to case RTJC and case to ambient.
E. The static characteristics in Figures 1 to 6 are obtained using <300Ps pulses, duty cycle 0.5% max.
F. These curves are based on the junction-to-case thermal impedence which is measured with the device mounted to a large heatsink, assuming
a maximum junction temperature of TJ(MAX)=175°C. The SOA curve provides a single pulse rating.
G. The maximum current rating is package limited.
H. These tests are performed with the device mounted on 1 in2 FR-4 board with 2oz. Copper, in a still air environment with TA=25°C.
THIS PRODUCT HAS BEEN DESIGNED AND QUALIFIED FOR THE CONSUMER MARKET. APPLICATIONS OR USES AS CRITICAL
COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS ARE NOT AUTHORIZED. AOS DOES NOT ASSUME ANY LIABILITY ARISING
OUT OF SUCH APPLICATIONS OR USES OF ITS PRODUCTS. AOS RESERVES THE RIGHT TO IMPROVE PRODUCT DESIGN,
FUNCTIONS AND RELIABILITY WITHOUT NOTICE.
Rev0 : Feb 2010
www.aosmd.com
Page 2 of 6



No Preview Available !

AOL1206
TYPICAL ELECTRICAL AND THERMAL CHARACTERISTICS
160
10V
140
6V 5V
120 4.5V
100
4V
80
60
3.5V
40
20
0
0
VGS=3V
1234
VDS (Volts)
Fig 1: On-Region Characteristics (Note E)
5
60
VDS=5V
50
40
30
20 125°C
10 25°C
0
1 1.5 2 2.5 3 3.5 4 4.5
VGS(Volts)
Figure 2: Transfer Characteristics (Note E)
10
8 VGS=4.5V
6
4
VGS=10V
2
0
0 5 10 15 20 25 30
ID (A)
Figure 3: On-Resistance vs. Drain Current and
Gate Voltage (Note E)
2
VGS=10V
1.8 ID=20A
1.6
17
1.4 VGS=45.5V
1.2 ID=15A2
10
1
0.8
0 25 50 75 100 125 150 175 200
Temperature (°C)
0
Figure 4: On-Resistance vs. Junction T1em8 perature
(Note E)
20
ID=20A
15
10 125°C
5
25°C
0
2 4 6 8 10
VGS (Volts)
Figure 5: On-Resistance vs. Gate-Source Voltage
(Note E)
1.0E+02
1.0E+01
40
1.0E+00
1.0E-01
125°C
25°C
1.0E-02
1.0E-03
1.0E-04
1.0E-05
0.0 0.2 0.4 0.6 0.8 1.0 1.2
VSD (Volts)
Figure 6: Body-Diode Characteristics (Note E)
Rev 0: Feb 2010
www.aosmd.com
Page 3 of 6



No Preview Available !

AOL1206
TYPICAL ELECTRICAL AND THERMAL CHARACTERISTICS
10
VDS=15V
8 ID=20A
2000
1500
6
1000
4
500
2
0
0 5 10 15 20
Qg (nC)
Figure 7: Gate-Charge Characteristics
0
0
Ciss
Coss
Crss
5 10 15 20 25
VDS (Volts)
Figure 8: Capacitance Characteristics
30
1000.0
100.0
10.0
RDS(ON)
limited
1.0
10Ps
10Ps
100Ps
1ms
DC 10ms
0.1 TJ(Max)=175°C
TC=25°C
0.0
0.01
0.1 1 10
VDS (Volts)
Figure 9: Maximum Forward Biased Safe
Operating Area (Note F)
100
140
TJ(Max)=175°C
120 TC=25°C
100
17
80 5
2
60 10
40
20
0.001
0.01
0.1
1
10
Pulse Width (s)
0
Figure 10: Single Pulse Power Rating J1u8nction-to-
Case (Note F)
10
D=Ton/T
In descending order
TJ,PK=TC+PDM.ZTJC.RTJC
D=0.5, 0.3, 0.1, 0.05, 0.02, 0.01, single pulse
RTJC=2.4°C/W
1
40
0.1
0.01
0.00001
PD
Single Pulse
Ton
T
0.0001
0.001
0.01
0.1
1
Pulse Width (s)
Figure 11: Normalized Maximum Transient Thermal Impedance (Note F)
10
100
Rev 0: Feb 2010
www.aosmd.com
Page 4 of 6



AOL1206 datasheet pdf
Download PDF
AOL1206 pdf
View PDF for Mobile


Related : Start with AOL120 Part Numbers by
AOL1202 30V N-Channel MOSFET AOL1202
Alpha & Omega Semiconductors
AOL1202 pdf
AOL1206 30V N-Channel MOSFET AOL1206
Alpha & Omega Semiconductors
AOL1206 pdf
AOL1208 30V N-Channel MOSFET AOL1208
Alpha & Omega Semiconductors
AOL1208 pdf

Index :   0   1   2   3   4   5   6   7   8   9   A   B   C   D   E   F   G   H   I   J   K   L   M   N   O   P   Q   R   S   T   U   V   W   X   Y   Z   

This is a individually operated, non profit site. If this site is good enough to show, please introduce this site to others.
Since 2010   ::   HOME   ::   Contact