AM2GW-NZ Datasheet PDF - AIMTEC

www.Datasheet-PDF.com

AM2GW-NZ
AIMTEC

Part Number AM2GW-NZ
Description DC-DC Converter
Page 2 Pages


AM2GW-NZ datasheet pdf
Download PDF
AM2GW-NZ pdf
View PDF for Mobile


No Preview Available !

FEATURES:
RoHS compliant
Ultra wide 4:1 input range
Remote On/Off Control
9 pin SIP package
Click on Series name for product info on aimtec.com
Series AM2GW-NZ
2 Watt | DC-DC Converter
Operating temperature -40oC to + 85oC
Continuous Short circuit protection
High efficiency up to 76%
Low ripple and noise
Models
Single output
Model
AM2GW -2405S-NZ
AM2GW -4805S-NZ
Input
Voltage (V)
9-36
18-72
Output
Voltage
(V)
5
5
Output Current
max
(mA)
400
400
Isolation
(VDC)
1500
1500
Max Capacitive
Load
(μF)
820
820
Efficiency
75
76
Input Specifications
Parameters
Nominal
Typical
Maximum
Voltage range
Filter
24 9-36
48 18-72
Capacitor
Maximum Rating
24 Vin
48 Vin
40
80
Peak Input Voltage time
On/Off Control
100
ON – low or open; OFF – high
On/Off input current
5 10
* Exceeding the maximum permissible value of 20mA for the Input On/Off current will damage the converter.
Isolation Specifications
Parameters
TestedI/O voltage
Resistance
Capacitance
Conditions
60 sec
At 500VDC
Typical
> 1000
80
Rated
1500
Units
VDC
VDC
ms
mA
Units
VDC
MOhm
pF
Output Specifications
Parameters
Voltage accuracy
Short Circuit protection
Short Circuit restart
Line voltage regulation
Load voltage regulation
Temperature coefficient
Ripple & Noise
Conditions
LL~HL
Load 10~100%
At 20MHz Bandwidth
Typical
±3
Continuous
Auto recovery
±0.75
±1.5
±0.03
100
Maximum
Units
%
%
%
%/oC
mV p-p
General Specifications
Parameters
Conditions
Typical
Maximum
Units
Switching frequency
Operating temperature
Storage temperature
Temperature rise
100% load, Vin nominal
With derating above 71oC
Full load
>100
15
-40 to +85
-50 to +125
550
35
KHz
oC
oC
oC
Cooling
Free air convection
Humidity
95 %
Case material
Non-conductive black plastic (UL94V-0 rated)
Weight
7g
Dimensions (L x W x H)
MTBF
1.02 x 0.37x 0.49 inch26.00 x 9.60 x 12.00 mm
>1 000 000 hrs (MIL-HDBK -217F, Ground Benign, t=+25oC)
NOTE: All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise
specified
www.aimtec.com
F 051e R6.F
Tel: +1 514 620 2722
1 of 2
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only



No Preview Available !

Pin Out Specifications
Pin Single
1 - V Input
2 + V Input
3 On/Off Control
6 + V Output
7 N.C.
8 N.C.
9 - V Output
Derating
Free Air Convection
100
80
Safe Operating Area
60
40
71ºC
20
0
- 40
- 20 0 20 40 60
Ambient Temperature º C
8085 100
0.50
(0.02)
2.54
(0.10)
Series AM2GW-NZ
2 Watt | DC-DC Converter
26.00
(1.02)
Dimensions
PRINTED
FACE
9.60
(0.37)
12.50
(0.49)
4.00
(0.16)
0.50
(0.02)
2.90
(0.11)
123
2.000
(0.079)
0.300 9.60
6 7 8 9 (0.012) (0.37)
0.50
(0.02)
Control ON/OFF pin connection example:
MCU
Vcc-5V
1K 1N4148
PIN 3
CONVERTER
The voltage could be applied through a limiting resistor and a switching diode. The converter is in a low power mode during
high level phase.
NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled
by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the
date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%,
nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components
and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This
product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate
specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com.
www.aimtec.com
F 051e R6.F
Tel: +1 514 620 2722
2 of 2
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only



AM2GW-NZ datasheet pdf
Download PDF
AM2GW-NZ pdf
View PDF for Mobile


Related : Start with AM2GW-N Part Numbers by
AM2GW-NZ DC-DC Converter AM2GW-NZ
AIMTEC
AM2GW-NZ pdf

Index :   0   1   2   3   4   5   6   7   8   9   A   B   C   D   E   F   G   H   I   J   K   L   M   N   O   P   Q   R   S   T   U   V   W   X   Y   Z   

This is a individually operated, non profit site. If this site is good enough to show, please introduce this site to others.
Since 2010   ::   HOME   ::   Contact