AAT3603 Datasheet PDF - Advanced Analogic Technologies

www.Datasheet-PDF.com

AAT3603
Advanced Analogic Technologies

Part Number AAT3603
Description Total Power Solution
Page 30 Pages


AAT3603 datasheet pdf
View PDF for PC
AAT3603 pdf
View PDF for Mobile


No Preview Available !

PRODUCT DATASHEET
AAT3603178
Total Power Solution for Portable Applications
General Description
The AAT3603 is a member of AnalogicTech’s Total Power
wwMwa.dnaatagsehmeeet4nut.cIoCmTM (TPMICTM) product family. It contains a
single-cell Lithium Ion/Polymer battery charger, a fully
integrated step-down converter and 5 low dropout (LDO)
regulators. The device is ideal for low cost handheld por-
table GSM or CDMA mobile telephones.
The battery charger is a complete thermally regulated
constant current/constant voltage linear charger. It
includes an integrated pass device, reverse blocking pro-
tection, high accuracy current and voltage regulation,
charge status, and charge termination. The charging
current, charge termination current, and recharge volt-
age are programmable with an external resistor and/or
by a standard I2C interface.
The step-down DC/DC converter is integrated with internal
compensation and operates at a switching frequency of
1.5MHz, thus minimizing the size of external components
while keeping switching losses low and efficiency greater
than 95%. All LDO output voltages are programmable
using the I2C interface.
The five LDOs offer 60dB power supply rejection ratio
(PSRR) and low noise operation making them suitable for
powering noise-sensitive loads.
All six voltage regulators operate with low quiescent cur-
rent. The total no load current when the step-down con-
verter and 2 LDOs are enabled is only 170μA.
The AAT3603 is available in a thermally enhanced low
profile 5x5x0.8mm 36-pin TQFN package.
Features
Voltage Regulator VIN Range: 4.5V to 6V
• Low Cost Power Integration
• Low Standby Current
170μA (typ) w/ Buck (Core), LDO1 (PowerDigital),
and LDO2 (PowerAnalog) Active, No Load
• One Step-Down Buck Converter (Core)
1.8V, 300mA Output
1.5MHz Switching Frequency
Fast Turn-On Time (120μs typ)
Five LDOs Programmable with I2C
LDO1: 3.0V, 300mA (PowerDigital)
LDO2: 3.0V, 150mA (PowerAnalog or PLL)
LDO3: 3.0V, 150mA (TCXO)
LDO4: 3.0V, 150mA (TX)
LDO5: 3.0V, 150mA (RX)
PSRR: 60dB@10kHz
Noise: 50μVrms for LDO3, LDO4, and LDO5
• One Battery Charger
Digitized Thermal Regulation
Charge Current Programming up to 1.4A
Charge Current Termination Programming
Automatic Trickle Charge for Battery Preconditioning
(2.8V Cutoff)
Adapter OK (ADPP) and Reset (RESET) Timer Outputs
• Separate Enable Pins for Supply Outputs
• Over-Current Protection
• Over-Temperature Protection
• 5x5mm TQFN55-36 Package
Applications
• Digital Cameras
• GSM or CDMA Cellular Phones
• Handheld Instruments
• PDAs and Handheld Computers
• Portable Media Players
3603.2008.06.1.0
www.analogictech.com
1



No Preview Available !

Typical Application
PRODUCT DATASHEET
AAT3603178
Total Power Solution for Portable Applications
www.datasheet4u.com
CHGIN
5V from
AC Adapter or USB Port
10μF
To BAT
100k
ADPP
STAT
ENBAT
To
BAT
100k
SDA
To 100k
BAT
SCL
EN_TEST
μC
EN_HOLD
EN_KEY
ON_KEY
RESET
To OUT1 100k EN2
EN3
EN4
EN5
AVIN2
To BAT
Charger
Control
Ref
I2C
and
Enable
Control
UVLO
BAT
22μF
+ 1 cell
- Li+
battery
VIN
Step-down
Ref BUCK
Enable
TS
CT
0.1μF
ISET
10kΩ
NTC
For BAT
Temp sense
1.24k
To BAT
PVIN
Core : 1.8V
LX 3.3μH
300mA
10μF
OUTBUCK
PGND
4.7μF
VIN
REF
CNOISE
To BAT
AVIN1
0.01μF
AGND
OUT5
RX
3.0V
150mA
OUT4
TX
3.0V
150mA
4.7μF
OUT3
TCXO
3.0V
150mA
4.7μF
OUT2
PowerAnalog
3.0V
150mA
4.7μF
OUT1
PowerDigital
3.0V
300mA
4.7μF
22μF
2
www.analogictech.com
3603.2008.06.1.0



No Preview Available !

PRODUCT DATASHEET
AAT3603178
Total Power Solution for Portable Applications
Pin Descriptions
Pin # Symbol
www.datasheet4u.com
1 EN_TEST
2 EN_HOLD
3 EN_KEY
4 ON_KEY
5 EN2
6 EN3
7 EN4
8 EN5
9 OUT5
10 OUT4
11 AVIN2
12 OUT3
13 OUT2
14 AVIN1
15 OUT1
16 AGND
17 CNOISE
18 RESET
19 ADPP
20 LX
21 PGND
22 PVIN
23 OUTBUCK
Function
Similar to EN_HOLD but intended for use with the automatic tester or as a hands free enable input pin indi-
cating hands free phone operation with a headset. It is also internally pulled to GND when oating.
Enable for the system. EN_HOLD must be held high by the processor to maintain core power. It is internally
pulled to GND when oating.
Enable for the system. An internal pull-up resistor keeps the pin pulled up to an internal supply to keep the
system off when there is no CHGIN input. Connect a normally-open pushbutton switch from this pin to GND.
There is an internal 300ms debounce delay circuit to lter noise.
Buffered logic output of the EN_KEY pin with a logic signal from ground to OUT1.
Enable for LDO2 (PowerAnalog or PLL). (Internally pulled low when oating)
Enable for LDO3 (TCXO). (Internally pulled low when oating)
Enable for LDO4 (TX) (Internally pulled low when oating)
Enable for LDO5 (RX) (Internally pulled low when oating)
Output for LDO5 (RX) (when shut down, pulled down with 10kΩ)
Output for LDO4 (TX) (when shut down, pulled down with 10kΩ)
Analog voltage input. Must be tied to BAT on the PCB.
Output for LDO3 (TCXO)
Output for LDO2 (PowerAnalog)
Analog voltage input. Must be tied to BAT on the PCB.
Output for LDO1 (PowerDigital)
Signal ground
Noise Bypass pin for the internal reference voltage. Connect a 0.01μF capacitor to AGND.
RESET is the open drain output of a 50ms reset timer. RESET is released after the 50ms timer times out.
RESET is active low and is held low during shutdown. RESET should be tied to a 10K or larger pullup to
OUTBUCK.
Open Drain output. Will pull low when VCHGIN > 4.5V. When this happens, depending on the status of the
USE_USB pin, the charge current will be reset to the default values (see Battery Charger and I2C Serial
Interface and Programmability section)
Step-down Buck converter (Core) switching node. Connect an inductor between this pin and the output.
Power Ground for step-down Buck converter (Core)
Input power for step-down Buck converter (Core). Must be tied to BAT.
Feedback input for the step-down Buck converter (Core)
24, 25
N/C No Connect; do not connect anything to these pins.
26, 27
28, 29
30
31
32
33
34
35
36
EP
BAT
CHGIN
ENBAT
TS
ISET
CT
STAT
SDA
SCL
EP
Connect to a Lithium Ion battery.
Power input from either external adapter or USB port.
Active low enable for the battery charger (Internally pulled low when oating)
Battery Temperature Sense pin with 75μA output current. Connect the battery’s NTC resistor to this pin and
ground.
Charge current programming input pin (Tie a 1k to GND for maximum fast charge current). Can be used to
monitor charge current.
Charger Safety Timer Pin. A 0.1μF ceramic capacitor should be connected between this pin and GND. Con-
nect directly to GND to disable the timer function.
Battery charging status pin output. Connected internally between GND and OUT1 (PowerDigital). Used to
monitor battery charge status.
I2C serial data pin, open drain; requires a pullup resistor.
I2C serial clock pin, open drain; requires a pullup resistor.
The exposed thermal pad (EP) must be connected to board ground plane and pins 16 and 21. The ground
plane should include a large exposed copper pad under the package for thermal dissipation (see package
outline).
3603.2008.06.1.0
www.analogictech.com
3



No Preview Available !

Pin Configuration
www.datasheet4u.com
PRODUCT DATASHEET
AAT3603178
Total Power Solution for Portable Applications
TQFN55-36
(Top View)
EN_TEST
EN_HOLD
EN_KEY
ON_KEY
EN2
EN3
EN4
EN5
OUT5
1
2
3
4
5
6
7
8
9
36 35 34 33 32 31 30 29 28
27 BAT
26 BAT
25 N/C
24 N/C
23 OUTBUCK
22 PVIN
21 PGND
20 LX
19 ADPP
10 11 12 13 14 15 16 17 18
4
www.analogictech.com
3603.2008.06.1.0



AAT3603 datasheet pdf
Download PDF
AAT3603 pdf
View PDF for Mobile


Related : Start with AAT360 Part Numbers by
AAT3601 Total Power Solution AAT3601
Advanced Analogic Technologies
AAT3601 pdf
AAT3601 Total Power Solution AAT3601
Skyworks
AAT3601 pdf
AAT3603 Total Power Solution AAT3603
Advanced Analogic Technologies
AAT3603 pdf

Index :   0   1   2   3   4   5   6   7   8   9   A   B   C   D   E   F   G   H   I   J   K   L   M   N   O   P   Q   R   S   T   U   V   W   X   Y   Z   

This is a individually operated, non profit site. If this site is good enough to show, please introduce this site to others.
Since 2010   ::   HOME   ::   Privacy Policy + Contact